- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
- Quick-drying water-based floor coating available in various greys.
- For concrete floors and old coatings.
- Satin matt finish.
- Good resistance to car tyres, diesel, motor oil, coolant fluid, and various household chemicals.
- Touch dry in just 2 hours.
Rust-Oleum 5200 Epoxyshield Ultra - Matt Finish Floor Coating
EpoxyShield ULTRA is a versatile, water-based floor coating designed for light to medium traffic areas. With its quick-drying formula, it is perfect for use on various concrete surfaces. Available in two shades of grey, this product ensures a durable, satin matt finish that enhances the aesthetic appeal of your floors.
Application Areas
This floor coating is suitable for:
- Concrete floors that are clean, dry, and treated with EpoxyShield Sealer 5220.
- Old, well-adhered coatings needing a fresh look.
- Areas exposed to light to medium foot traffic and limited vehicular traffic.
Application Instructions
For optimal results, follow these steps:
- Ensure the concrete surface is free from oil, grease, and other contaminants.
- Allow new concrete to cure for at least 30 days.
- Remove any laitance, loose concrete, and repair cracks with EpoxyShield concrete repair products.
- Apply EpoxyShield Sealer 5220 to absorbent, porous surfaces for better adhesion.
- Stir the coating material thoroughly before use.
- Apply with a nylon paint roller, possibly requiring two coats to achieve the prescribed film thickness.
Restrictions and Limitations
- Do not apply to smooth and completely sealed concrete or surfaces with curing compounds.
- Not recommended for floors subjected to prolonged contact with water.
- Avoid using in temperatures below 10°C or above 35°C and relative humidity above 85%.
- Always ensure the surface is at least 3°C above the dew point during application.
MSDS Summary
- EpoxyShield ULTRA is non-hazardous under EC Regulation 1272/2008.
- Ensure to follow all safety guidelines provided in the MSDS.
Data sheet
- For Use By
- Consumer Use
- Interior / Exterior Use
- Interior Use
- For Use On
- Concrete Floors
- Application Method
- Brush
Roller - Sheen
- Satin
- VOC Levels
- Low (50-149 g/l)
- Single, Two or Three Pack
- Single
- Pack Size
- 5L
- Dry to Handle (at 20°C)
- 6 Hours
- Dry to Recoat (at 20°C)
- 6 Hours
- Fully Cured (at 20°C)
- 1 Week
- Coverage
- 9m² per litre
- Max. Application Temperature
- 35°C
- Min. Application Temperature
- 10°C
- Solids by Volume
- 38% - 42%
- VOC
- 72g/L
- Shelf Life (from date of manufacture)
- 5 years
- Touch Dry
- 2 Hours
- Recommended Dry Film Thickness
- 40 µm
- Recommended Wet Film Thickness
- 100 µm
- Base Type
- Water-Based
- Suitable For Use On
- Concrete Floors
- Suitable For Use On
- Garage Floors
- Finish
- Matt
- Application Method
- Brush
- Application Method
- Roller
- Usages
- Abrasion Resistant
- Usages
- Oil Resistant
- Usages
- Chemical Resistance
- Product Usage Type
- Topcoat
- Fastest Delivery
- Next Working Day
- Colour Family
- Grey
- Product Type
- Epoxy-Modified Acrylic
Questions
Question about the product
Ashley on 2024-04-08 10:44:21 | Question:
The floor area that I want to cover is 3 x 3m. So a 5L tin will cover as stated. The floor has some slight imperfections. How thick is the covering of a 5L tin, so that it will self level? |
Answer from Rawlins’ Technical Team:
Thank you for your enquiry. This product has a theoretical consumption rate of 9m2/litre at 40 microns DFT (Dry-Film Thickness), with the recommended two coat application this would be a total of 80 Microns DFT. | |
James on 2023-08-13 09:42:56 | Question:
How many litres would I need for two coats on a single garage floor? |
Answer from Rawlins’ Technical Team:
This would depend on how large the area is you need to cover. The coverage rate of this product is 9m² per litre per coat. In the case of roller application it can be necessary to apply 2 coats. | |
Karla on 2022-07-31 22:19:21 | Question:
Would this be ok ok a terracotta tiled floor?? |
Answer from Rawlins’ Technical Team:
Assuming the terracotta tiled floor is porous, only subjected to foot traffic, it is clean, dry, sound and prepared as detailed in the technical data sheet this could be used. | |
robert young on 2022-03-08 14:54:56 | Question:
I am looking to paint my garage floor with Rust-Oleum 5200 Epoxyshield Ultra. As in most garages, the majority of the concrete floor is internal. However about 30cm of it protudes externally under the garage door, so it is permanently external. Can i use the 5200, with 5220 sealer, on this portion as well as on the internal garage floor? Is there anything suitable to apply on top of the 5200 if needed, or is the 5200 still OK in external as well as internal? Many thanks |
Answer from Rawlins’ Technical Team:
Yes these products can be applied to concrete internally or externally. There is not a topcoat we can recommend to over paint this with. | |
John Knight on 2021-12-15 15:55:16 | Question:
Going to put this on my garage floor, approximately 30 years old. do I need to put a sealer on first or is it ok to apply this only. |
Answer from Rawlins’ Technical Team:
Assuming the garage floor is clean, dry, sound and prepared as detailed in the technical data sheet, in most circumstances grinding the floor or acid etching the concrete will be required prior to application, then Rust-Oleum 5220 Epoxyshield Sealer should be applied prior to application of the floor paint. | |
Jason on 2021-02-28 15:49:12 | Question:
Can I use the RUST-OLEUM EPOXYSHIELD DECORATIVE FLAKES with this paint?.Also,can you apply this paint with a brush? Thank you. |
Answer from Rawlins’ Technical Team:
Rust-Oleum Epoxyshield Decorative Flakes are designed for use with 2 pack epoxy coatings such as the Rust-Oleum Garage Floor Kit or Rust-Oleum 5300 Epoxyshield Maxx. It is likely that the paint film will be too thin if using 5200 Epoxyshield Ultra to get a good hold of the flakes and ensure they stay in place. Rust-Oleum 5200 Epoxyshield Ultra can be applied with brush or roller. | |
oliver on 2019-09-18 17:25:53 | Question:
can this be used on setcrete high performance self levelling compound. This SLC is designed as a wear surface. What primer would I use in conjunction with the SLC and Epoxy Ultra? Many Thanks |
Answer from Rawlins’ Technical Team:
If the self levelling product you have used can be left as a wearing surface and the manufacturer of the product is happy for it to be coated with single pack water-based floor coatings (epoxy-modified acrylic) then yes Rust-Oleum 5200 Epoxyshield Ultra could be used. The data sheet for Rust-Oleum 5200 Epoxyshield Ultra states the followin under preparation; Remove oil, grease and all other contaminants with Rust-Oleum Epoxyshield Cleaner / Degreaser in combination with high pressure cleaning. Allow new concrete to set for at least 30 days before applying a coating. Remove laitance, loose and damaged concrete by sandblasting or etching with Rust-Oleum Mathys 108 Surfa Etch Solution. Repair all holes and cracks with EpoxyShield concrete repair products. Always pre-treat absorbent, porous surfaces with Rust-Oleum 5220 Epoxyshield Sealer. Roughen or blast well-sealed and smooth concrete and treat withRust-Oleum 5220 Epoxyshield Sealer or apply a coat Rust-Oleum 3333 Super Adhesion Primer. Roughen still-intact floor coatings to ensure good adherence. Remove poorly adhering old coatings with wire brush and sandpaper. During application the surface must be clean and dry. | |
Laura on 2019-02-28 18:08:14 | Question:
I used one cost of the rustoleum 5200 Epoxy sealer last year on my concrete floor. Is it Ok to now use this epoxy paint to paint over it. Even though the sealer was put on about 8 months ago. I have cleaned the floor thoroughly. Will it still work well or do I need to grind it back to the original concrete & start from scratch? |
Answer from Rawlins’ Technical Team:
Rust-Oleum 5220 Epoxyshield Sealer is recommended to prime/seal floors before Rust-Oleum 5200 Epoxyshield Ultra so you will not need to remove it. Before applying Rust-Oleum 5200 Epoxyshield Ultra, ensure the floor is clean, dry and lightly sand the Rust-Oleum 5220 Epoxyshield Sealer if necessary to remove any gloss and provide a key. | |
Olly on 2018-11-12 22:38:08 | Question:
I have a concrete floor slab, flat but only hand smoothed. Is the sealer/primer a necessity? |
Answer from Rawlins’ Technical Team:
Yes, the data sheet states 'Always pre-treat absorbent, porous surfaces with Rust-Oleum 5220 Epoxyshield Sealer.' | |
Harriet wright on 2018-11-07 09:15:58 | Question:
Would thus paint be suitable for use on floorboards in a bedroom and do you need to use a primer with it as old floorboards are currently bare wood. |
Answer from Rawlins’ Technical Team:
Rust-Oleum 5200 Epoxyshield Ultra is recommended for concrete surfaces, for domestic floorboards customers have previously used Blackfriar Professional Acrylic Floor Paint. Bare surfaces require a sealer (Blackfriar Professional Water Based Floor Sealer or for small areas dilute Blackfriar Professional Acrylic Floor Paint with 10% water), then apply 2 coats of the floor paint as recommended. | |
Jonty on 2018-05-01 09:50:26 | Question:
Can I use this rust-eleum 5200 to put over a pre existing vinyl floor? |
Answer from Rawlins’ Technical Team:
No. | |
Barbara Smart on 2017-09-06 13:41:36 | Question:
Is the water based rust oleum 5200 epoxyshiled ultra a low odour paint?
Thanks |
Answer from Rawlins’ Technical Team:
Being water based, when used in the intended industrial/commercial environments Rust-Oleum 5200 Epoxyshield Ultra is indeed a low odour paint. Please note however this does not mean a NO odour paint. | |
Vladimira Kezele on 2017-03-17 21:31:43 | Question:
Can Epoxyshield 5200 Ultra be used for covering o an old concrete path around the house (outside)?
If not, what would you recommend for outside old concrete? |
Answer from Rawlins’ Technical Team:
Rust-Oleum Tarmacoat has a larger colour range and would be more suited to this type of external application. | |
Lisa Buckland on 2015-08-04 08:50:36 | Question:
Can Rust-Oleum 5200 Epoxyshield Ultra be used on wooden floorboards in a kitchen? |
Answer from Rawlins’ Technical Team:
No, but you could use Timberex Aqua Plus | |
IMPORTANT SHIPPING & DELIVERY INFORMATION
Rust-Oleum 5200 Epoxyshield Ultra is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Rust-Oleum Epoxyshield Cleaner / Degreaser
Clear, colourless cleaning liquid. For coated, mineral, and steel substrates. Removes grease, oil, and other contaminants. Virtually odour-free and non-flammable. Can be used with sponges, brushes, or high-pressure cleaners.
Rust-Oleum Epoxyshield Decorative Flakes
Suitable for use on floors coated with Epoxyshield. Mix and match chip blends to customise your colour scheme. Helps to hide dirt and surface imperfections. Durable and long-lasting finish. Easy to apply.
Rust-Oleum 5200 Epoxyshield Ultra
Quick-drying water-based floor coating available in various greys. For concrete floors and old coatings. Satin matt finish. Good resistance to car tyres, diesel, motor oil, coolant fluid, and various household chemicals. Touch dry in just 2 hours.
Rust-Oleum 5300 Epoxyshield Maxx
A water-based industrial floor coating available in greys. For use on trafficked concrete floors. Highly resistant to solvents, chemicals, and car tyres. Easy to apply with no primer required. Long-lasting, glossy finish.
Rust-Oleum Epoxyshield Fine Crack Repair
Available in Grey. Ideal for repairing fine cracks up to 3 mm wide on concrete floors. Non-shrink, solvent-free epoxy for durable repairs. Quick drying time: 3-4 hours.
Rust-Oleum Epoxyshield Garage Floor Coating Kit
Available in grey. For clean and dry concrete floors, including old adhering coatings. Resistant to gasoline, antifreeze, motor oil, salt, and hot tire pick-up. Comes with a complete kit and detailed instructions for easy application.
Rust-Oleum Epoxyshield Concrete Repair Mortar
Available in grey. Powdered repair mortar for levelling and repairing concrete. Also for cement renderings and unpainted brickwork. Internal or external use. Recoatable after 48 hours, traffic allowed after 24 hours. Professional use only.
Rust-Oleum 5220 Epoxyshield Sealer
Clear gloss finish. Water-based sealer for concrete. Reduces dust, simplifying cleaning. For bare and clean concrete floors. No thinning required. Touch dry in 1 hour, walkable after 8-12 hours.
Floor Application Kit
Floor Application Kit from Rawlins Paints provides all the application equipment needed to apply conventional floor paints and coatings to a professional standard. The application of floor coatings is often crucial to their performance, so it is important to use the right tools to ensure a lasting finish. Each kit contains: 12" Roller,...