- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Tikkurila Fontecoat EP 50, a two-component water-borne epoxy topcoat and a single-coat paint recommended for framework, service platforms, conveyors and other steelwork, machinery and equipment. The product has MED (Marine Equipment Directive) certificate no VTT-C-12360-15-18 and is thus accepted for painting surfaces inside ships.
- Huge colour range from RAL, BS & NCS
- Fast curing
- For steel surfaces
- Environmentally friendly (low VOC emissions)
- Good resistance against mechanical and chemical stress
- Provides protection comparable to that of solvent-borne epoxy paints.
- Resistant to diesel and biodiesel (RME) fuel
- If used as a primer, a popular shade would be Tikkurila TVT 722K Beige, which can be chosen in the colour picker below
Product customisation
Don't forget to save your customization to be able to add to cartTikkurila Fontecoat EP 50 is a two-component water-borne epoxy topcoat and a single-coat paint. Used as a single-coat paint, primer, intermediate coat or topcoat in epoxy or polyurethane systems for steel surfaces. It dries rapidly and can be applied in thick layers.
An ideal option when a low VOC content is required. The paint has very good resistance against mechanical and chemical stress and provides protection comparable to that of solvent-borne epoxy paints.
Fontecoat EP 50 can be primed with the solvent-borne adhesion primer Temakeep. The system has extremely good adhesion and surface tolerance. At the same time, it is possible to achieve a very rapid production cycle.
Quick Links - Click To Jump To Section:
- Features & Benefits
- Technical Data
- Surface Preparation
- Recommended Primers
- Recommended Topcoat
- Application Conditions
- Mixing Components
- Application
- Thinner/Cleaning
- VOC
- Health And Safety
Features & Benefits
- Huge colour range from RAL, BS & NCS
- A semi-gloss epoxy paint to be used as a single-coat paint, primer, intermediate coat or topcoat in epoxy or polyurethane systems for steel surfaces
- It dries rapidly and can be applied in thick layers
- An ideal option when a low VOC content is required.
- The paint has very good resistance against mechanical and chemical stress
- The product provides protection comparable to that of solvent-borne epoxy paints
- Can be primed with the solvent-borne adhesion primer Temakeep
- The system has extremely good adhesion and surface tolerance
- At the same time, it is possible to achieve a very rapid production cycle
- Fast curing and environmentally friendly (low VOC)
- Resistant to diesel and biodiesel (RME) fuel
- Recommended for framework, service platforms, conveyors and other steelwork, machinery and equipment
- The product has MED (Marine Equipment Directive) certificate no VTT-C-12360-15-18 and is thus accepted for painting surfaces inside the ships
Technical Data
- Volume Solids: 47±2% (ISO 3233)
- Weight Solids: 62±2%
- Specific Gravity: 1.4 kg / l (mixed)
- Mixing Ratio:
- Base - 1 part by volume Fontecoat EP 50
- Hardener - 1 part by volume 007 1019
- Pot life (23℃): 1½ hours
Recommended Film Thicknesses and Theoretical Coverage
Recommended film thicknesses | Theoretical coverage | |
---|---|---|
Wet | Dry | |
130µm | 60µm | 7.7 m²/l |
215µm | 100µm | 4.7 m²/l |
225µm | 120µm | 3.9 m²/l |
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.
Drying Times
DFT 100 µm | 15°C | 23°C | 35°C |
---|---|---|---|
Dust dry, after | 4h | 2h | 1h |
Touch dry, after | 8h | 5h | 2h |
Recoatable by itself, min. after | 16h | 6h | 4h |
Recoatable without roughing, max. after | 7d | 5d | 2d |
Fully cured, after | 14d | 7d | 3d |
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation
Surface Preparation
Oil, grease, salts and dirt are removed by appropriate means. (ISO 12944-4)
Steel surfaces: Blast clean to grade Sa2½. (ISO 8501-1) If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.
Primed surfaces: Oil, grease, salt and dirt are removed from the surface by appropriate means. Repair any damage to the primer coat. Note the overcoating time of primer. (ISO 12944-4)
Recommended Primers
- Fontecryl AP
- Fontezinc 85
- Fontecoat EP 50 Beige
- Fontecoat EP 50
- Temazinc 99
- Temacoat GPL-S Primer
(Overcoating on touch dry surface)
Recommended Topcoat
- Fontecoat EP 50
- Fontedur HB 80
Application Conditions
- All surfaces must be clean, dry and free from contamination.
- The temperature of the ambient air, surface and paint should not fall below +15ºC during application and drying.
- Relative humidity of the air should not exceed 70% during application and drying.
- The surface temperature of steel should remain at least 3°C above the dew point.
- Good ventilation and sufficient air movement is required in confined areas during application and drying.
- Tinting, mixing ratio, thinning, film thickness and drying conditions can effect the gloss
Mixing Components
- First stir base and hardener separately.
- The correct proportions of base and hardener must be mixed thoroughly before use.
- Use power mixer for mixing.
- Insufficient mixing or incorrect mixing ratio will result in uneven drying of the surface and weaken the properties of the coating.
Application
Airless Spraying
- The product is thinned approximately 0–10%.
- Recommended nozzle tip is 0.011"–0.023" and pressure 140–200 bar.
- Spray angle shall be chosen according to the shape of the object.
- DFT 160μm should not be exceeded.
Conventional Spraying
- The product is thinned approximately 5–10%.
- Recommended nozzle tip is 1.8–2.0 mm and pressure 3–4 bar.
Brush Application
- The product should be thinned according to the circumstances.
Thinner/Cleaning
Thinner
Water.
Cleaning Of Equipment
Clean the spraying equipment immediately after use as follows:
- Run the equipment with water to remove excess paint from the equipment.
- Run the equipment with a mixture of approx 20% Thinner 1109 in clean water, at least two times.
- Finally wash with undiluted Thinner 1109.
Wash the equipment with water before starting to paint again. Unwashed equipment can cause serious surface defects.
VOC
The Volatile Organic Compounds amount is 60g/litre of paint mixture. VOC content of paint mixture (thinned by 10% by volume) 55g/l.
Health And Safety
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets.
For industrial and professional use only.
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 (option 2) or send a message to [email protected] for more information.
Data sheet
- Manufacturer
- Tikkurila
- Interior / Exterior Use
- Interior & Exterior
- For Use On
- Steel
- Application Method
- Brush, Spray
- Sheen
- Semi Gloss
- Colour
- Fully Tintable
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 10L
- Parts
- Two
- Base Type
- Water-borne epoxy
- Interior/Exterior Use
- Both
- Solvent
- Mixed - see Safety Data Sheet
- Mixing Ratio
- 1:1
- Suitable Substrates
- Steel
- Application
- Brush, Spray
- Coverage
- 3.9 m²/l - 7.7 m²/l
- Recommended Thinner/Cleaner
- Water
- Min. Application Temperature
- 15ºC
- Solids by Volume
- 47±2%
- VOC
- 55g/l
- Finish
- Semi Gloss
- Recommended Dry Film Thickness
- 60µm - 120µm
- Recommended Wet Film Thickness
- 130µm - 225µm
- UN Number (Activator)
- N/A
- UN Number (Base)
- UN3082
- Dry to Recoat (at 23°C)
- 6hrs
- Fully Cured (at 23°C)
- 7 days
- Pot Life
- 1½ hours (at 23ºC)
- Base Type
- Epoxy
- Base Type
- Water-Borne
- Suitable For Use On
- Steel
- Finish
- Semi-Gloss
- Application Method
- Brush
- Application Method
- Spray
- Product Usage Type
- Topcoat
- Product Range
- Fontecoat
- Colour Family
- Black
- Colour Family
- White
- Colour Family
- Neutral
- Colour Family
- Anthracite Grey
- Colour Family
- Grey
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Brown
- Colour Family
- Pink
- Colour Family
- Orange
- Colour Family
- Purple
- Colour Family
- Yellow
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Tikkurila Fontecoat EP 50 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Tikkurila Fontecryl AP
Tikkurila Fontecryl AP is a water-borne, one-component fast-drying acrylic based primer for various surfaces containing active anti-corrosive pigments. Provides excellent adhesion Used as an anti-corrosive primer on steel, aluminium and zinc surfaces Suitable for dipping Can be overcoated both with water and solvent-borne topcoats Wide...
Tikkurila Fontedur HB 80
Tikkurila Fontedur HB 80, a two-component, water-borne polyurethane topcoat for use on steel surfaces exposed to weathering, abrasion and chemical stress. Recommended to be used for agricultural and earth moving machinery, steel framework and other steel structures, machinery and equipment. Huge colour range available from RAL, BS & NCS...
Tikkurila Fontezinc 85
Tikkurila Fontezinc 85 is a two-component, water-borne zinc-rich epoxy paint that is a more environmentally friendly option for bridges, cranes and steel framework as well as steelwork and equipment in the forest and chemical industries. Offers cathodic protection of steel For paint systems in severe environments Can withstand severe...
Tikkurila Temazinc 99
Tikkurila Temazinc 99, a 2-component, polyamide cured zinc-rich epoxy paint providing superior cathodic protection for steel, used as a primer in epoxy, polyurethane, acrylic and chlorinated rubber systems for steel surfaces exposed to severe climatic conditions. Prequalified in the NORSOK system 1; an excellent choice for the most...
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...