Thermoguard Timbercoat 60 Minute System is a coloured intumescent paint system for interior and exterior timber surfaces. Each pack contains the correct amount of basecoat (Timbercoat) and topcoat (Smoke and Flame Retardant Dualcoat) to ensure protection is achieved inline with the manufacturers recommendations to the respective area in...
Thermoguard Wallcoat 30 & 60 Minute System for Plasterboard is a coloured intumescent paint system for interior plasterboard and cement board ceiling and wall surfaces. These packs have been created to help users ensure they are purchasing sufficient product for their project. Each pack contains the correct amount of basecoat (Wallcoat)...
Thermoguard Wallcoat BS Class 1/0 & EN Class B System is a coloured fire retardant paint system for interior plasterboard ceiling and wall surfaces. Each pack contains the correct amount of basecoat (Wallcoat) and topcoat (Wallcoat Smoke & Flame Retardant Topcoat) to ensure protection is achieved inline with the manufacturers...
Thermoguard Thermocoat W is a White Intumescent Paint for steel, structural steel and cast iron:
Up to 120 minutes’ fire resistance
Can be overcoated with compatible decorative topcoat
Water-based
Low odour
Environmentally friendly
Cost effective for large projects
Certificate of supply available on request
Can be applied by brush,...
This category lists intumescent paints and coatings for structural steel sections that can provide fire resistance for up-to 60 minutes in the event of exposure to cellulosic fire. They will react to the heat from a fire by expanding to form a protective char layer of differing depths, dependant on product.
Please check product descriptions for fire rating compliance, application methods – brush, roller, or airless sprayer - colour options, and product compatible system recommendations – primers, basecoats, or topcoats.
Intumescent Paint for Steel disclaimer: Always ensure the product you are purchasing is suitable for the intended use/project. This will include but is not limited to gaining clarification that the product in question can achieve the required fire protection for the steel sections and environment you have. The sub-categories within the Intumescent Paints for Steel section allow users to filter by internal or external use, on-site or off-site application, and product type – water-based, solvent-based, epoxy-based and MMA-based. These are to be used as a guide only as there will be instances where a product will be able to achieve 90min protection on certain steel section sizes but not others, or where it is suitable for external use in environments up to C4 but not C5-M for example. For further product, project and pricing support, we ALWAYS recommend you contact our Technical Department before purchase and use.
Fire protection doesn’t have to be hard work, let our technical staff help you get the level of protection you require and the finish you want. If there is a product you cannot find, please contact our Technical and Sales Support Team on 0113 245 5450.
Rust-Oleum Hard Hat Topcoat is the number 1 industrial paint aerosol, a top quality high performance topcoat available in 45 RAL colours for use on on bare metal, wood and concrete.
Fast drying - touch dry in just 15 minutes (at 20°C)
Best available hiding power
Heat-resistant up to 100°C
Based on lead and chromate-free pigments
Up to...
Sika CarboDur S NSM are pultruded carbon fibre plates for structural strengthening as part of a Sika CarboDur system. Sika CarboDur plates are pultruded carbon fibre reinforced polymer (CFRP) laminates, designed for strengthening concrete, timber and masonry Sika CarboDur plates are bonded into slots as near surface mounted reinforcement using...
Thermoguard Intumescent Mastic is an easy to apply, intumescent sealant that provides a 5 hour fire barrier coupled with excellent sound reduction properties. Permanently flexible and excellent slump resistance it is ideal for sealing gaps around fire doors, window frames and for sealing joints, voids and irregular holes in fire rated...
General Painting Application Kit from Rawlins Paints provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site.
Provides an economical way of making sure you will have what you need
Ideal for interior and exterior paint projects
Each kit contains:...
International Interzone 101 is a two component, solvent free epoxy which can be applied underwater to give a corrosion and abrasion resistant coating. Intended for use as a hand-applied repair compound for application to submerged steelwork and splashzone areas of offshore jackets, piling and other permanently wet areas where conventional...
Sikafloor EpoCem Module is a solvent free, two-component, water based, epoxy resin primer for the Sika EpoCem range of products.
It is suitable for use in hot and tropical climates. Excellent bonding promoter on cementitious and other mineral based substrates, supplied in pre-measured packs and can be applied to damp substrates.
More...
GacoPro Roof Coating is a professional grade, 150% elastic, 100% silicone roof paint for flat and pitched roofs that can be applied year-round and guarantees protection and waterproofing for 20 years.
Solar reflective - energy saving
Flexible
Protects against leaks, ponding water, and severe weather
Single pack
Cuts roof maintenance...
Rust-Oleum Biosan Aqua Matt is ideal for walls and ceilings where hygiene control is essential in low wear areas. Offers high durability, perfect saponification resistance, particularly high covering capacity and helps to maintain a hygienic environment.
Available in 100+ RAL & BS colours
Decorative hygienic paint in gloss, satin or...
Teamac Marine Gloss is a high quality, modified long oil alkyd marine coating. It has excellent gloss and opacity.
High gloss
Excellent opacity and adhesion
Touch dry in as little as 4 hours (at 20°C)
Full hardness in 5 - 7 days
Suitable for all general marine areas, bridge fonts, deck work, masts, superstructures etc
Click to jump...
Rust-Oleum 2901 Epoxyshield Cleaner/Degreaser for floors is a concentrated, alkaline, non-flammable, virtually odour-free cleaning/degreasing solution.
Removes grease, oil and other contaminations
Virtually odour free
Non-flammable
6-8 m²/l coverage
More Information
**Available for delivery - see Delivery Options below**
Rust-Oleum Mathys Metal Cladding Topcoat is a long lasting water based, semi-gloss acrylic paint specially designed for use as a finish on exterior metal cladding that has high filling and hiding power and features excellent flow out with high durability and colour and gloss stability.
Choose from 350+ colours from RAL & BS
New formula...
Rust-Oleum 5180 Epoxy Repair Mortar is an incredibly tough, 2 component epoxy resin mortar for repairing damaged, dished or dangerous concrete and stone floors.
Virtually indestructable
Heavy traffic friendly
Chemical resistant
Does not shrink or crack
Easy all-in-one packaging
Interior/Exterior use
No primer required in most...
60-minute fire rated Intumescent coatings for steel available at Rawlins Paints can be applied to galvanised steel, mild steel and cast iron. Always check product data sheets for a full substrate application guide, to ensure that a product is suitable, and manufacturer recommended for use on specific types of steel. Alternately, contact Rawlins Paints’ technical support team, where we will be able to provide more in-depth product information, along with recommending full intumescent paint systems for steel.
Product data sheets will dictate optimal fire protection and resistance from successful application, including:
Maximum achievable film thickness per coat (microns)
All of the intumescent paints we offer have been tested to varying British/European standards by recognised independent third parties depending on their required use and performance. In addition to these industry standard tests, some products also offer additional paperwork after use by way of a ‘certificate’ that can be obtained in different ways - manufacturer dependent. Some require a form to be completed and returned by email, others have online application forms, others can be simply called to provide project details verbally. Not ALL products offer this additional supplement and if this type of certificate is important to your project you should contact our Technical Team on 0113 2455450 (option 2) or [email protected] to advise them of this so they can ensure they recommend a suitable product accordingly. Certain larger projects may also require the involvement of an independent inspector, again you should contact our Technical Department to discuss this if required.
Our help and advice promise
Fire protection doesn’t have to be hard work, let our technical staff help you get the level of protection you require and the finish you want. Whether it’s structural steel in a warehouse, fire retardant paint for wood on a new-build, or the internal walls of a block of flats, we can provide a full specification and offer guidance throughout the project.
