Axalta ViterClad 50 Finish is a two pack recoatable polyurethane finish specially formulated for the maintenance and repainting of architectural cladding, especially recommended for the maintenance of Corus Colorcoat HP200 and HPS200 cladding. Available in 350+ colours Expected system lifetime up to 15 years (depending on exposed...
Bradite One Can is a quick-drying primer/finish coat in one can, with excellent adhesion, stain blocking and anti-corrosive properties. Suitable for use over most properly cleaned and prepared commercial wood, uPVC, glass, plastic and metals. Manufactured under the auspices of an ISO 9001:2008 & ISO 14001:2004. Advantages Available in...
Bradite Industrial Degreaser is an aqueous alkaline low foaming detergent used for degreasing contaminated surfaces prior to painting. Ideally suited for degreasing oily or soiled surfaces and for removing road dirt. Manufactured under the auspices of an ISO 9001:2008 & ISO 14001:2004. Advantages Biodegradable in general use...
Bradite Pre-Treat Galvanised Steel is a mordent solution used as a pre-treatment for galvanised steel, to provide a key for all paint primers and finishes. Easy to use solution; clean up with water after use. Advantages British gas reference BGC MO1. Department of Transport Item NO:155. ISO 9001:2008 ISO 140001:2004 1 x 1l available...
90 Mins - Internal Use
Intumescent paints and coatings are available for both internal and external application on structural steel, although some are designed and tested specifically for internal use only. These internal use only intumescent coatings will usually offer excellent cost benefits, and are generally suitable for horizontal and vertical girders, columns and hollow section steel members, for on-site application in heated, dry internal environments. Internal intumescent coatings may not be suitable for areas subject to high humidity, moisture content or other challenging conditions.
Locations that internal use intumescent paint for steel to provide passive fire protection to structural steelwork while maintaining architectural aesthetics for commercial infrastructure assets include Airports, leisure facilities, Commercial buildings, Retail complexes, etc.
Intumescent Paint for Steel disclaimer: Always ensure the product you are purchasing is suitable for the intended use/project. This will include but is not limited to gaining clarification that the product in question can achieve the required fire protection for the steel sections and environment you have. The sub-categories within the Intumescent Paints for Steel section allow users to filter by internal or external use, on-site or off-site application, and product type – water-based, solvent-based, epoxy-based and MMA-based. These are to be used as a guide only as there will be instances where a product will be able to achieve 90min protection on certain steel section sizes but not others, or where it is suitable for external use in environments up to C4 but not C5-M for example. For further product, project and pricing support, we ALWAYS recommend you contact our Technical Department before purchase and use.
Fire protection doesn’t have to be hard work, let our technical staff help you get the level of protection you require and the finish you want. If there is a product you cannot find, please contact our Technical and Sales Support Team on 0113 245 5450.
Jotun Steelmaster 1200WF is a one component waterborne acrylic thin film intumescent coating independently tested and approved for fire protection of structural steel exposed to cellulosic fire up to 180 minutes. Suitable for properly prepared carbon steel substrates.
Jotun Steelmaster 120SB is a one component solvent based acrylic thin film intumescent coating independently approved for fire protection of structural steel exposed to celulosic fire. It can be used as mid coat or finish coat in atmospheric environments and is suitable on approved primers on carbon steel and galvanised steel substrates.
Thin film water-borne intumescent coating optimized for 90 and 120 minutes fire resistance, as part of the Interchar range for cellulosic fire protection, International Interchar 1190 will maintain your architectural aesthetics for fire resistance periods up to 120 minutes on structural steelwork. Coverage Calculator
International Interchar 2090 is a single component, solvent borne, borate free, high solids, low VOC intumescent coating designed to maintain your architectural aesthetics whilst providing fire protection for up to 120 minutes for columns, I-sections, cellular beams and hollows. Coverage Calculator
International Interchar 212 is a high performance, high build, solvent free, two pack modified epoxy intumescent fireproofing coating designed to be used on steelwork requiring protection from cellulosic fires.
Nullifire SC801 On-Site Water-Based Intumescent Basecoat is a water-based, white, thin film intumescent coating for the protection of internal structural steelwork, providing up to 120 minutes fire resistance.
Thermoguard Thermocoat W is a White Intumescent Paint for steel, structural steel and cast iron: Up to 90 minutes’ fire resistance Can be overcoated with compatible decorative topcoat Water-based Low odour Environmentally friendly Cost effective for large projects Certificate of supply available on request Can be applied by brush,...
Sherwin-Williams Firetex FX1003 is a single pack, thin film intumescent coating, designed for site application by airless spray, to provide ﬁre resistance for up to 120 minutes on structural steel.
Sherwin-Williams Firetex FX5090 is a water based TCEP free thin film intumescent coating, designed for application by airless spray to provide fire resistance for periods of up to 120 minutes on structural steel.
Sherwin-Williams Firetex FX5120 is a water based TCEP free thin film intumescent coating. Firetex FX5120 has been designed for application by airless spray, to provide fire resistance for periods of up to 120 minutes on structural steel. FX5120 can also be used to enhance the fire resistance of concrete slabs and decks up to 60 minutes.
International Interchar 1120 is a single component, borate and chlorine free, water borne intumescent coating designed for on-site application to interior exposed structural steel requiring protection from cellulosic fire. A low VOC intumescent material independently fire tested that will maintain your architectural aesthetics for fire...
International Interchar 1290 is a thin film waterborne intumescent coating optimised for hollow sections up to 180 minutes fire resistance whilst still maintaining aesthetics. Interchar 1290 is a single component, borate and chlorine free, water borne intumescent coating designed for on-site application to structural steel requiring protection...