HMG Thinner 2611


    HMG Thinner 2611 is a medium thinner.

    • For use with compatible HMG systems.

    £10.65(ex. VAT)
    £12.78 (inc. VAT)
    Please choose your colour
    Available for Delivery (See Delivery Options Below)


    HMG Thinner 2611 is a medium thinner.

    Click To Jump To Section:

    Features & Benefits

    • For use with compatible HMG systems.

    Suitable for use with the following HMG products:

    Product Specification

    Technical Data
    HMG Thinner 2611
    Volume Solids:0.0%
    VOC Content:0.778kgs/ltr
    Viscosity:2 mPas
    Density:0.765 g/cm³
    Storage Conditions:Store between 5°C - 25°C. When not in use, cans must be kept sealed.
    Shelf Life:12 months from delivery date in original sealed containers.
    Flash Point:38°C

    Surface Preparation

    • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
    • Read and follow the safety data sheet, product data sheet and label instructions.
    • Stir all paints thoroughly before use.
    • Always use the same batch number on the same job.
    • Check colour & sheen.
    • Filter the product immediately before use.
    • Reduce emissions and maintain quality by replacing tin lid after use.

    Product Notes

    Information On Basic Physical And Chemical Properties
    HMG Thinner 2611
    Form:According to product specification
    Colour:According to product specification
    Odour Threshold:Not determined
    pH-value 20°C:Not determined
    Melting point/freezing point:Undetermined
    Initial boiling point and boiling range:139°C
    Flash Point:38°C
    Flammability (solid, gas):Not applicable
    Ignition temperature:200°C
    Decomposition temperature:Not determined.
    Auto-ignition temperature:Product is not selfigniting.
    Explosive properties:"Product is not explosive. However, formation of explosive air vapour mixtures are possible."
    Explosion limits: Lower:0.6 Vol %
    Explosion limits: Upper:7 Vol %
    Vapour pressure at 20°C:Not determined
    Density at 20°C:0.765 g/cm³
    Relative density:Not determined
    Vapour density:Not determined
    Evaporation rate:Not determined
    Solubility in / Miscibility with water:Fully miscible
    Partition coefficient: n-octanol/water:Not determined
    Viscosity: Dynamic at 20°C:2 mPas
    Viscosity: Kinematic:Not determined
    Solvent content: Organic solvents:100.0%
    Solids content:0.0%

    Health & Safety

    • Refer to the safety data sheet in the attachments section above and tin label prior to use.

    Click to go back to the top of the page

    Product Details

    Data sheet

    HMG Paints Limited
    0.765 g/cm³
    Solids by Volume
    Shelf Life (from date of manufacture)
    12 months from delivery date in original sealed containers.
    1L & 5L
    UN Number
    Product Type
    Categorised As
    Accessories > Thinners

    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

    Be the first to ask a question about this product!

    Question about the product

    * Required fields


    HMG Thinner 2611 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT

    You might also like

    HMG C71 Speedline

    HMG C71 Speedline is a high quality, single pack, synthetic alkyd enamel suitable for brushing or spraying. Offers fast surface drying, good through drying (even in thick films), and a hard, tough finish, with minimal yellowing even at high temperature - ideal for machinery, appliance and agricultural projects.For use on ferrous and...

    Price £20.65 (ex. VAT)
    In Stock and Available for Delivery

    HMG Coach Enamel

    HMG Coach Enamel is traditional, ultra high quality, high build, long oil synthetic enamel for brush application.  It gives an extra long wet edge time allowing it to be brushed without brush drag.High gloss Excellent water resistance Flexible with good exterior durability and toughness Available in 3,500 colours from RAL, NCS, and...

    Price £22.63 (ex. VAT)
    In Stock and Available for Delivery

    HMG D66 Economy Line

    HMG D66 Economy Line is an alkyd based synthetic enamel designed for general purpose brush and spray requirements.  It is also oil and diesel resistant making it a good choice for agricultural, appliance & machinery finishes.Good performance Oil and diesel resistant Quick drying agricultural paint Quick drying appliance paint...

    Price £19.32 (ex. VAT)
    In Stock and Available for Delivery

    HMG 14 Line Fleet Polyurethane

    HMG 14 Line Fleet Polyurethane is a high build, high solids polyurethane based on a unique blend of polyurethane alkyds.  It combines a long wet edge time with excellent hot spray application offering superb durability and gloss retention.Can be brushed directly from the can or with the addition of a small amount of thinner Suitable for...

    Price £22.63 (ex. VAT)
    In Stock and Available for Delivery

    HMG Synthetic BDX Primer

    HMG Synthetic BDX Primer is a high build, anti-corrosive, single pack alkyd primer for use under all HMG synthetic topcoats, combining high build and excellent sandability with outstanding application and scratch filling properties.For use on suitably prepared structural steel, chassis, fabrication and aluminium Can be applied to bare...

    Price £15.11 (ex. VAT)
    In Stock and Available for Delivery

    HMG KX Undercoat

    HMG KX Undercoat is a high build polyurethane alkyd undercoat.Offers excellent wet edge characteristics and superb topcoat holdout Formulated for use under all HMG Synthetic topcoats Available in 5,000+ colours from RAL, NCS, and British Standard Also available as an aerosol, please see HMG KX Undercoat AerosolPlease note: Colours...

    Price £18.52 (ex. VAT)
    In Stock and Available for Delivery

    HMG Synthetic High Opacity Undercoat

    HMG Synthetic High Opacity Undercoat is a 1K alkyd/polyurethane undercoat with superior brushing qualities and excellent obliteration properties.Suitable for large areas due to its ease of application and long wet edge time Please note: Colours shown are for illustrative purposes onlyMore Information Delivery Info

    Price £37.74 (ex. VAT)
    In Stock and Available for Delivery