• Sherwin-Williams Epidek M153

Sherwin-Williams Epidek M153

M153

Sherwin-Williams M153 is an aggregate dressed, ultra heavy duty, hard wearing, coal tar free, solvent-less epoxy anti-slip deck coating. It is used for the treatment of deck surfaces subject to the most extreme of operational conditions requiring a high degree of impact and abrasion resistance.

  • Epoxy anti-slip deck coating
  • For the treatment of deck surfaces subject to the most extreme of operational conditions
  • Complies with NORSOK M501 (Rev.5) System 4 
  • Two component

Colour
Size
Finish
£328.23
VAT excluded

£393.88 Tax incl.
Quantity

Description

Sherwin-Williams M153 is an aggregate dressed, ultra heavy duty, hard wearing, coal tar free, solvent-less epoxy anti-slip deck coating. It is used for the treatment of deck surfaces subject to the most extreme of operational conditions requiring a high degree of impact and abrasion resistance, and where a high level of anti-slip properties need to be retained under conditions of severe crude oil and hydrocarbon contamination. 

Endorsements

Complies with NORSOK M501 (Rev.5) System 4 

Recommended Primers/Topcoats

  • Macropoxy C425V2 Zinc Phosphate Primer/Buildcoat
  • Macropoxy L425 Zinc Phosphate Primer
  • Macropoxy M262 Hi-Build Finish 

Application Conditions & Overcoating

It is preferred that whenever practical Epidek M153 should be applied directly on to blast cleaned steel to Sa21⁄2. M153 may be applied over an approved high build epoxy primer.

If applied over Macropoxy Blast Primer the primer thickness must be carefully controlled. The target DFT is 25μm but the maximum DFT applied must not exceed 40μm. If a high build primer is required please use one of those recommended on the front of this data sheet.

This material should preferably be applied at temperatures in excess of 10°C. In conditions of high relative humidity, ie 80-85% good ventilation conditions are essential. Substrate temperature shall be at least 3°C above the dew point and always above 0°C.

At application temperatures below 10°C, drying and curing times will be significantly extended, and spraying characteristics may be impaired.

Application at ambient air temperatures below 5°C is not recommended.
If it is desired to overcoat outside the times stated on the data sheet, please seek advice of Technical Team.

Packaging

A two component package comprising Component ‘A’ and ‘B’

Component A (20 litre pail); Containing 12.6 litres base screed unit comprising epoxy resin base, curing agent and fine silica grit.

Component B (nylon sack); Containing 25kg calcined bauxite aggregate (see below).

Pack Size: 12.6 litre unit when mixed
Mixing Ratio: 1.54 parts base to 1 part additive by volume plus silica grit
Weight: 1.84 kg/litre (may vary with shade).
Shelf Life: 2 years from date of manufacture or ‘Use By’ date where specified.

Additional Notes

Drying times, curing times and pot life should be considered as a guide only.

The curing reaction of epoxies commences immediately the two components are mixed, and since the reaction is dependent on temperature, the curing time and pot life will be approximately halved by a 10°C increase in temperature and doubled by a 10°C decrease in temperature.

Calcined Bauxite Aggregate

Four sizes of aggregate are available depending on degree of anti-slip properties required and end use:-
1. Light Aggregate (0.85 - 1.70mm )
2. Medium Aggregate (1.40 - 2.00mm )
3. Heavy Aggregate (1.40 - 2.80mm)
4. Road Aggregate (3.00 - 5.00mm)

N.B. Consumption of aggregate will depending upon screed thickness, efficiency of excess aggregate recovery and recycling. For guidance on quantities of aggregate consult sheet entitled Epigrip M153 Supplementary Information.

Overcoating

If it is felt desirable to overcoat the surface of Epidek M153 Heavy Duty Deck Coating or to mark surfaces with a different colour this may be achieved by the application of a coat of Macropoxy M262 Hi-Build Finish.

Numerical values quoted for physical data may vary slightly from batch to batch.

Product Details
M153

Data sheet

Application Method
Trowel
Sheen
Mid Sheen
Colour
Standard / Ready Mixed
VOC Levels
Ultra-Low (5-49 g/l)
Single, Two or Three Pack
Two-Pack
Product Certifications
NORSOK M501 (Rev.5) System 4
Pack Size
12.6L
Coverage
0.32m² per litre
Touch Dry
5 Hours
UN Number (Activator)
UN3469
UN Number (Base)
UN1263
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send