This pack provides sufficient intumescent basecoat (Zeroflame Aquasteel WB+) and coloured topcoat (Zeroflame Aquasteel WB+ Finish) to protect suitably primed, standard structural steel beams and columns in internal environments to 60 minute fire resistance.
Sherwin-Williams Firetex FX2003
Sherwin-Williams Firetex FX2003 is single pack thin ﬁlm intumescent coating, designed for in-shop application by airless spray to provide ﬁre resistance for up to 120 minutes on structural steel.
After appropriate drying, Firetex FX2003 speciﬁcations can be exposed to the weather for up to 6 months provided that the speciﬁc use or storage does not lead to ponding water due to rainfall, condensation or other site/transportation/storage circumstances.
Firetex FX2003 can resist normal weather conditions for up to 6 months without topcoat provided it has had appropriate drying prior to exposure. Once an approved topcoat has been applied as appropriate to the prevailing conditions, then durability will be substantially enhanced. If the speciﬁc use or storage could lead to prolonged contact with water due to rainfall, condensation, or other site/transportation/storage circumstances, then a recommended topcoat must be used to prevent damage to the basecoat.
Certiﬁre Approved – Certiﬁcate CF5077
This product has been assessed in accordance with the Criteria of Acceptability given in the ASFP/BCF “Industry Guidance Document“. This product has been tested and assessed in accordance with the ASFP ﬁretesting protocol for cellular beam protection. See Section 6.3 from ASFP “Yellow Book” 4th Edition.
For in-shop application, use Firetex C69 Fast-Track Blast Primer. Several primers have been approved for use under Firetex FX2003. Please consult our technical team for detailed information.
For certain dry, internal situations where the ﬁnal colour/appearance is not critical, then Firetex FX2003 may remain un-topcoated. For externally exposed steelwork and severe internal environments Acrolon C137V2 or Acrolon C237 must be used as a topcoat. For other internal environments where a topcoat is required then Firetex M71V2 or Sher-Cryl M770 should be used. In all instances for subsequent re-decoration, use Firetex M71V2, Sher-Cryl M770, Acrolon C137V2 or Acrolon C237 as appropriate.
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
Be the first to ask a question about this product!
Nullifire SC602 On-Site Intumescent Base Coat, a single pack acrylic thin film intumescent basecoat for fire protection of internal & semi-exposed structural steelwork up to 60 minutes. Easy to apply, designed for on-site application by airless spray Weather resistance (up to 6 months once cured) ensures more effective project planning...
Intershield Flexible Top Coat is part of the Intumescent Coating for Steel & Aluminium Protection range, helping protect steelwork with extra fire protection. Chlorinated rubber flame retardent Complies with BS476 Parts 6 & 7, Class 0 & Class 1 (1987) Spread of flame Apply by brush, roller or sprayer No thinning required
Nullifire SC801 On-Site Water-Based Intumescent Basecoat is a water-based, white, thin film intumescent coating for the protection of internal structural steelwork, providing up to 120 minutes fire resistance.
Thermoguard Thermocoat S, an intumescent anti-fire paint for structural steel and cast iron. Provides up to 90 minutes fire resistance, maintaining the structural integrity of buildings. UKAS/ EGOLF Fire Test Laboratory Certification to BS 476 Part 21 Fire Resistance to load bearing elements of structures Contact our technical team for...
Jotun Steelmaster 120SB is a one component solvent based acrylic thin film intumescent coating independently approved for fire protection of structural steel exposed to celulosic fire. It can be used as mid coat or finish coat in atmospheric environments and is suitable on approved primers on carbon steel and galvanised steel substrates.
EP/FS/TCW Water-Based Top Coating for Steel is part of the Intumescent Coating for Steel & Aluminium Protection range, helping protect steelwork with extra fire protection. Hard & glossy top coat Good weather resistance Apply with a brush, roller or spray For internal & non-exposed areas
International Interchar 2060 is a single component, solvent borne, borate free, high solids, low VOC, thin film intumescent coating optimized for 60 minutes fire resistance to structural steelwork. Independently tested at accredited laboratories to BS476 Parts 20-21, AS 1530.4-2005 and AS 4100, and third party assessed and certified.
International Interchar 1120 is a single component, borate and chlorine free, water borne intumescent coating designed for on-site application to interior exposed structural steel requiring protection from cellulosic fire. A low VOC intumescent material independently fire tested that will maintain your architectural aesthetics for fire...
Sherwin-Williams Firetex FX5120 is a water based TCEP free thin film intumescent coating. Firetex FX5120 has been designed for application by airless spray, to provide fire resistance for periods of up to 120 minutes on structural steel. FX5120 can also be used to enhance the fire resistance of concrete slabs and decks up to 60 minutes.
Thermoguard Thermocoat W is a White Intumescent Paint for steel, structural steel and cast iron: Up to 90 minutes’ fire resistance Can be overcoated with compatible decorative topcoat Water-based Low odour Environmentally friendly Cost effective for large projects Certificate of supply available on request Can be applied by brush,...
Sherwin-Williams Firetex FX5062 is a water-based TCEP free thin film intumescent coating, specifically designed for airless spray application to provide fire resistance for periods up to 90 mins on structural steel. Firetex FX5062 has been Certifire Approved.
Sherwin-Williams Firetex FX1003 is a single pack, thin film intumescent coating, designed for site application by airless spray, to provide ﬁre resistance for up to 120 minutes on structural steel.
International Interchar 1260 is a single component, borate, chlorine and APEO free, water borne intumescent coating designed for on-site application to interior exposed structural steel requiring protection from cellulosic fire.
Jotun Steelmaster 60SB is a one component solvent based acrylic thin film intumescent coating independently approved for fire protection of structural steel exposed to cellulosic fire. It can be used as a mid coat or finish coat in atmospheric environments and is suitable on approved primers on carbon steel and galvanised steel substrates.
A one-component, thin-film solvent-borne intumescent coating for fire protection of circular and rectangular hollow section structural steel. Top Features Tested and assessed to EN 13381-8 CE marked product, ETA 15/0053 Assessed to ETAG 018-2 for all durability classifications