Coo-Var Profloor 2 Pack Epoxy Floor Paint is an exceptionally hard wearing water-based, solvent free two pack epoxy floor paint coating, suitable for heavy duty traffic and wear. It can be used for projects both inside or outside and is ideal for use in heavy traffic areas with fork trucks and vans.
RSL Resufloor FX
Resuflor FX is a modified polyurethane epoxy resin floor finish that creates a flexibility, making it ideal for flooring systems with slight movement. It has a 2.5mm-3mm smooth gloss finish.
- Accommodates floors/decking where flexing is expected
- Chemical resistance
- Easy to clean
Resuflor FX is ideal for large timber floors, mezzanine floors or steel decking which can often expect movement. Like the Resutop range it is very hard-wearing, dealing with chemicals, abrasion, and user-friendly when it comes to maintaining.
It is decorative, self-smoothing and comes in an array of colours, making it both practical and aesthetically apt for a nightclub, or perhaps a domestic studio. Its durability and easy-to-clean complexion means it is also suitable for shopping outlets and commercial stores.
- Buildings with plywood or chipboard flooring
- Television studios
- Mezzanine areas both domestic and commercial
- Printing and packaging warehouses
New Concrete Floors: New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm sq. is required.
Existing Concrete Floors: Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue of detergent is washed and removed by rinsing with clean water. Local repairs should be carried out using Resupatch.
Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with existing floor coating.
Where over-coating other systems such as epoxy coatings or screeds, as part of a specified composite system in the data sheets, please follow the recoat time as stated in the individual data sheets, the coating in each stage should be tack free, but not fully cured. If fully cured, then mechanical preparation is required to ensure intercoat adhesion.
Timber Floors: Must be clean, sound and dry. Old clear varnish/topcoat must be removed/sanded prior to application, as it may affect the inter- coat adhesion with Resuflor FX.
Open and porous substrates will require priming with Resuprime NT on dry substrates only with less than 75% ERH reading. Where the relative humidity of a substrate exceeds 75% ERH, R.S. Dampshield or R.S. Dampshield FH should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.
The number of coats to be applied is chosen in accordance with the following table.
ERH% Required Coating Thickness
75-85 1coat of R.S.DAMPSHIELD or DAMPSHIELD FH at 200 microns per coat
85-92 2coats of R.S.DAMPSHIELD or DAMPSHIELD FH at 200 microns per coat
92-97 3coats of R.S.DAMPSHIELD or DAMPSHIELD FH at 200 microns per coat For
Further information please refer to recommended individual product data sheets.
The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 10°C.
Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally to allow the ambient and substrate temperature to stabilise prior to installation.
Mixing: Pre-mix the coloured component (base) to a uniform colour, then mix the entire contents of base with the hardener. If a separate mixing bucket is being used ensure all contents of both components are removed from the buckets supplied. Mix using a slow speed electric mixer for approximately one to two minutes until the two components have fully combined then add the aggregate slowly.
Mix for a further 1-2 minutes until the aggregate has fully combined and there are no lumps. The mixed unit should be applied immediately.
Resuflor FX should be worked with a trowel or float to achieve an even smooth finish. This is best achieved by the application of smooth even pressure with the compound poured over the correct coverage rate after fixing the stop ends to control the flow of the material. Then roll the area with a spiked roller to achieve an even smooth surface and remove entrapped air. Do not re-roll the area later than 15-20 mins.
The surface should be protected from temperatures of less than 10°C and moisture in the early stages of cure. This could adversely affect the flow, levelling and surface finish of Resuflor FX.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Trowel, Spiked Roller.
- 5 sq. m per 29.5kg unit @ 3mm thickness.
- Touch Dry
- 24-32 Hours
Be the first to ask a question about this product!
Sikafloor 390 is a 2-part, flexible and chemically resistant, coloured epoxy coating. It is crack-bridging and chemically resistant for concrete and screed surfaces in bund areas for the protection against water contaminating liquids.
Sikafloor 264 N Thixo is a two part, economic, coloured epoxy resin textured roller and seal coat. This Sikafloor product is solvent free, thixothropic grade for high build textured and structured finishes.
Coo-Var Dampshield is a gas permeable epoxy resin membrane tolerant of residual moisture in concrete floor, enabling earlier covering. ADVANTAGES Enables resin finishes sooner Easy application Can be applied to substrates with hygrometer readings up to 97% RH Solvent free Low odour
Sherwin-Williams Macropoxy M262 (formerly Epigrip M262) is a 2-pack epoxy high build gloss finish for interior or exterior use in conjunction with appropriate primers and undercoats. It is suitable for application on concrete floors.
Rust-Oleum 5300 Epoxyshield Maxx is a user friendly and easy to apply water-based 2 component epoxy concrete floor coating with an ultimate adhesion and durability: Maximum durability in just 1 coat For medium to heavy traffic Easy to apply, no primer required Long-lasting gloss finish Highly resistant against solvents and chemicals...
Resutop FH is a fast curing, two-pack epoxy resin coating in one application that creates a seamless finish when chemical, abrasion, and impact resistance flooring is essential. ADVANTAGES Recoat period of 4 hours at 20°C Non-toxic and solvent-free Good light reflection Good colour stability No shrinkage on curing Easy to clean Anti-slip is...
Nu-Base HB Epoxy Floor Finish is a two-pack floor resin for use in most industrial floors concrete and wood. Achieves a non-tainting finish which is is ideal for use in dairies, breweries and the food industry. Advantages Epoxy resin for concrete or wood flooring Solvent and dust free Non-tanning Odour-free
Resuprime is a two-pack, solvent-free epoxy resin bonding and priming coat. It bonds resin-based screeds and toppings to cementitious and other surfaces. ADVANTAGES Versatile for many types of application Excellent adhesive properties Easy to apply Can be used as a tack coat for screeds No unpleasant or harmful odours Image already added
A two-pack, specialist primer for surfaces with residual oil contamination. Ideal for concrete floors and screeds, promotes adhesion prior to coating with Blackfriar Professional High Traffic Floor Paint.
Resuscreed 55 is a flecked epoxy resin floor screed for concrete, wood metal and other surfaces with sound and clean substrates. It produces a seamless finish to new and existing floors. ADVANTAGES Hard wearing Can be a repair system Feather edged option Low odour Can be used to form coving and falls Abrasive/Impact resistant Image already...
Rust-Oleum Powerfloat Epoxy Floor Primer Rapid 3366 is a rapid curing 2-component solvent-free epoxy primer designed to improve the adhesion of coatings to difficult substrates such as power-floated concrete.
This product is now only available with a minimum order of 800 litres. For an alternative, please contact our sales team on 0113 2455450 or via the contact form. Jotun Jotafloor Solvent Free Primer is a transparent two component, polyamine cured, and solvent free epoxy coating. It ensures very good adhesion on most concrete floors in...
R.S. Oil Tolerant Primer is a two-component epoxy resin floor membrane that combats any residual oil that has escaped into a concrete floor. It ensures that no oil will affect a top finish. ADVANTAGES Easy application Application onto substrates with engineering oil contamination Excellent adhesion Low odour High solids Image already added
Coo-Var Profloor Plus Cold Cure is a low temperature curing version of Coo-Var Profloor Plus. This two-pack, solvent free epoxy resin coating is designed to cure when the surface temperature is in the range 0 to 10°C. Coo-Var Profloor Plus Cold Cure is particularly valuable for applications at colder times of the year when the cure time of the...
307 Flexible Deck Coat is a solvent free, flexible resin coating modified to impart toughness, resilience and waterproofing properties. The abrasion and impact resistance, together with the low temperature flexibility and excellent adhesion to concrete, make 307 Flexible Deck Coat ideal for surfaces subjected to frequent vehicular traffic.