Teamac Protector II Antifouling

525/C259/ ALL

Teamac Protector II Antifouling is used as an antifouling coating for the underwater areas of vessels or underwater structures. Designed for vessels with a max speed of 25 to 30 knots. Expected functional life of the coating is 12 to 18 months.

  • Contains cuprous oxide to give good antifouling performance
  • Ideal for steel, wood, ferro concrete or GRP hulls
  • Available in 3 colours
  • Suitable for domestic and commercial use
  • Click to jump down to Technical Data

Colour
Size
£26.32
VAT excluded

£31.59 Tax incl.
Quantity

Description

Teamac Protector II Antifouling contains cuprous oxide to give good antifouling performance. Designed for marine vessels with a max speed of 25 to 30 knots. Expected functional life of the coating is 12 to 18 months. It is used as an antifouling coating for the underwater areas of vessels or underwater structures.

Suitable for domestic and commercial vessels with steel, wood, ferro concrete or GRP hulls.



Click To Jump To Section:




Features & Benefits


  • Antifouling for the underwater areas of vessels or underwater structures
  • Contains cuprous oxide to give good antifouling performance
  • Ideal for steel, wood, ferro concrete or GRP hulls
  • Expected functional life of the coating is 12 to 18 months
  • Available in 3 colours
  • Suitable for domestic and commercial use



Product Specification


Technical Data
Volume Solids 63%
VOC Content Max 330 g/litre
SG 1.6 to 1.65 @ 20°C
Viscostity 4.5 Poise @ 25°C
Flash Point Above 32°C (closed cup)



Film Thickness Range and Coverage


Product Data
  Dry Film Thickness Wet Film Thickness Theoretical Coverage
Maximum 63 µm 100 µm 10 m2/litre. 63 microns dft. application.
The practical spreading rate may be lower as this depends on factors such as the porosity and roughness of the surface to be painted and material losses during application.



Drying Times


Drying Times At 20°C/RH 50%
Touch Dry: 3 Hours
Dry To Recoat: 16 Hours
Fully Cured: 18 Hours

Low temperature and high humidity will adversely affect application, drying and performance of any coating.



Surface Preparation


  • New steel: Abrasive blast clean to Sa2½ and apply TEAMAC METACLOR UNDERWATER PRIMER. If applying onto shop-primed steel ensure that surface is dry and clean, and areas of damaged primer are suitably cleaned prior to the application of the METACLOR.

  • Maintenance: Remove all loose and damaged existing coating, and all marine growth. High pressure wash with fresh water. Areas of breakdown should be blasted or power tool cleaned. Touch up with METACLOR PRIMER to the full existing film thickness. Prior to the application of the full coat ensure that surface is clean and free of all contaminates.



Mixing


Mix well before use.



Application Conditions


As dictated by normal good painting practice. Care must be taken during application that the temperature is above the dew point to avoid any contamination. It may be necessary to apply PROTECTOR ANTIFOULING in a number of coats to achieve the specified film thickness.



Application Methods


Method Airless Spray Conventional Spray Brush Roller
  No* No* Yes Yes



  • *APPLICATION BY SPRAY IS NOT PERMITTED EXCEPT BY PROFESSIONALS.
  • Nozzle Size: 0.021" - 0.027"
  • Nozzle Pressure: 3600 psi (250 bar)



Health & Safety


Users must comply fully with all their legal responsibilities under the Control of Pesticides Regulations 1986 (as amended), including complying with all conditions of approval. H.S.E. Approval No 8375. Launch time after painting - minimum 8 hours, maximum 3 months if shrouded from direct sunlight. Minimum 2 coats.

See safety data sheet - SDS 10964. To avoid risks to man and the environment users must comply with the instructions for use.

Click to go back to the top of the page

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
525/C259/ ALL

Data sheet

For Use On
Steel, Wood, Ferro Concrete, GRP
Application Method
Brush, Roller, Spray
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Single
Pack Size
1L, 2.5L, 5L
Parts
One part pack
Suitable Substrates
Steel, wood, ferro concrete or GRP hulls
Application
Brush, Roller, Spray
Dry to Recoat (at 20°C)
16 Hours
Fully Cured (at 20°C)
18 Hours
Coverage
10m² per litre
Recommended Thinner/Cleaner
Thinners 17
VOC
Max 330 g/litre
Touch Dry
3 Hours
Size
1 litre, 2.5 litre, 5 litre
Recommended Dry Film Thickness
63 µm
Recommended Wet Film Thickness
100 µm
UN Number
1263
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


questions Joe mcgunnigle on 2019-12-14 19:45:45
Question: 

Can this be used on fibreglass boats

Answer: 

Yes, refer to the product data sheets available to download from the 'Attachments' tab for details on preparation, priming, application, etc.

questions Dave Mortlock on 2018-08-06 20:58:22
Question: 

Hi ,could you tell me is your teamac protector antifoul paint suitable to overcoat international cruiser uno antifoul. Thanks

Answer: 

Yes, Teamac Protector Antifouling can be applied directly to International Cruiser Uno, 2 coats are preferred.


Question about the product

* Required fields
(read)
Send
You might also like

Teamac Metaclor Antifouling Primer

Teamac Metaclor Antifouling Primer, previously know as Teamac Metaclor Underwater CR Primer, is a strong, versatile, chlorinated rubber based coating for Wood, Metal & GRP.  Suitable for Narrowboats, Cruisers, Barges, Yachts and Marine Applications.  Can be used above and below the waterline, on mixed material surfaces and over any...

Price £18.25
In stock