- There are no more items in your cart
- Shipping Calculated at checkout
- Sub-Total(ex. VAT)(inc. VAT)£0.00£0.00
RSL Resutop Cold Cure
We no longer stock this product, but can recommend RSL Resutop FH as a great alternative.
We no longer stock this product, but can recommend RSL Resutop FH as a great alternative.
Resutop CC is the coolest member of the Resutop family, making it ideal for beverage areas that require a colder temperature.
When kept at 5°C, it can be re-coated every 18 hours, leaving a tough, abrasive, and attractive flooring with optional anti-slip aggregates.
This makes Resutop CC perfect for a workplace which requires a colder climate, whilst maintaining safe wet and dry surfaces to the same exceptional standard that Resutop delivers in hotter environments.
The full range of Resin Surfaces Limited colours are available.
Recommended Uses
- Food and beverage warehouses
- Gyms
- Aviation areas
- Schools
- Showrooms
- Cool chemical plant rooms
Preparation
New Concrete Floors: New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm sq. is required.
Existing Concrete Floors: Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue of detergent is washed and removed by rinsing with clean water. Local repairs should be carried out using Resupatch or Resuscreed 45.
Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with existing floor coating.
Where Resutop CC is applied to masonry/concrete surfaces, care must be taken to ensure that surface preparation is thorough but does not disfigure the surface.
Priming
Open and porous substrates may require priming with Resuseal WB, also Resuprime NT or Resucoat HB may be used as primer on the dry substrates only with less than 75% ERH reading.
Where the relative humidity of a substrate exceeds 75%, ERH, R.S. Dampshield should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.
The number of coats to be applied is chosen in accordance with the following table:
ERH% Required Coating Thickness
75-85 1coat of R.S.DAMPSHIELD at 200 microns per coat
85-92 2coats of R.S.DAMPSHIELD at 200 microns per coat
92-97 3coats of R.S.DAMPSHIELD at 200 microns per coat
For Further information please refer to recommended individual product data sheets.
Application
The ambient temperatures of the areas should not be allowed to fall below 10°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 5°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally to allow the ambient and substrate temperature to stabilise prior to installation.
Mixing: Pre-mix the coloured base component to a uniform consistency then mix the entire contents of the base with the hardener. If a separate mixing bucket is being used mix thoroughly ensuring all contents of both components are removed from the buckets supplied. Mix using a slow speed electric mixer for approximately two to three minutes until the two components have fully combined.
The mixed unit should be applied immediately by squeegee, roller or brush with a consistent procedure. Floor areas should be cross-rolled to ensure even application and to minimise roller marks. Coverage rates may vary depending on profile and porosity of the substrate.
Data sheet
- Application
- Brush, Roller, Squeegee.
- Coverage
- 5Kg. will cover 19m sq. @ 200 microns.
- Touch Dry
- 18 Hours
- Brand
- RSL
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
RSL Resutop Cold Cure is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT