Bradite Cladit+

PC76 / PG77

We no longer stock this product, but can recommend Axalta ViterClad 50 Finish as a great alternative.

Product customisation

Don't forget to save your customization to be able to add to cart
  • 250 char. max
Quantity
Product not available
This Product has been Discontinued

Description

We no longer stock this product, but can recommend Axalta ViterClad 50 Finish as a great alternative.

Bradite Cladit+ (PC76) is a cladding paint which has excellent adhesion to existing cladding coatings (e.g. coil, plastisol and powder coatings) with minimal preparation.

The main purpose of Bradite Cladit+ (PC76) is to renovate cladding, providing a weather and light resistant coating that is flexible and hard-wearing. Suitable for use over most existing cleaned and prepared cladding coating systems.

Bradite Cladit+ (PG77) is a high performance two-pack polyurethane finish for suitably primed steel and non-ferrous substrates. Providing exceptional weather and water resistance, the solvent-based coating  produces a tough and hard wearing coating that is recoatable even after long periods of exposure. Please note; the gloss version (PG77) is intended for professional use only.

Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems. 2004/42/EC EU limit value for this product (cat.A/d sb): 300g/l (2010). This product contains max.198 g/l VOC.


Features & Benefits

  • Available in more than 350 colours in RAL & BS
  • Tough and hard-wearing.
  • Flexible film coating.
  • Cures at low temperatures.
  • Excellent colour retention.
  • Resistance to weathering.
  • High build acrylic semi-gloss finish.


Preparation

High pressure water cleaning to remove all loose and flaking paint and contamination back to a sound substrate. Bradite TD39 industrial strength detergent washing and rinsing should be used with scrubbing to remove grease or oil. Check & confirm adhesion of apparently sound cladding coating by carrying out cross hatch adhesion test to all elevations. If adhesion is suspect then elevation should be completely stripped of old coating and repainted. Intact areas of existing coatings should, ideally, be roughened by manual or mechanical sanding. Feather back exposed areas to a sound coating edge. Cracks and pits should be filled using a suitable filler before painting. Substrate should be dust free and completely dry before coating. Exposed ferrous substrate should be blast cleaned to SIS Sa21/2 or manually cleaned to SIS St3, then patch primed with Bradite Surface Tolerant Epoxy Primer EP92*.

Painting System

Priming coat: Bradite Surface Tolerant Epoxy Primer EP92 (if required)*

1st coat: Bradite CLADIT+ Semi Gloss PC76

2nd coat: Bradite CLADIT+ Semi Gloss PC76*

*For non-ferrous surfaces use, Bradite Barrier Primer EU96 instead.

Always refer to the Health and Safety sheet for the product before use, and observe the warning phrases on the label.


Application

Always aim to paint an elevation preceding direct sunlight illumination to prevent painting onto warm surfaces which may cause too rapid drying and detract from application properties and finish appearance quality. Application and use should always conform to the codes of practice described in BS 6150 and BS 5493.

Brush and Roller: Supplied ready for use. Thin with 0-10% Bradite Thinner TP33 if required.

Conventional Air Spraying: Thin with 10-20% Bradite Thinner TP33 as required, tip size - 2.0mm, tip pressure 60psi (0.4MPa) approximately.

Airless Spraying: Thin with 0-15% Bradite Thinner TP33 as required, tip size - 18 thou (0.46mm) approximately, tip pressure - 2100 psi (15MPa) approximately.

Clean all equipment immediately after use with Bradite Thinner TP33 for best results.

Product Details
PC76 / PG77

Data sheet

Manufacturer
Bradite
Interior / Exterior Use
Exterior
For Use On
Plastisol, Powder Coatings, Steel, Non-ferrous metals
Application Method
Brush, Roller, Spray, Airless Spray
Sheen
Semi-Gloss
Single, Two or Three Pack
Two-Pack
Product Certifications
ISO 9001:2008, ISO 14001:2004 environmental management systems
UN Number
UN1263
Brand
Bradite
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send