Call 0113 245 5450 for Sales or Technical
Alternatively you can email our sales & support team on [email protected]
Sherwin-Williams FIRETEX M95/02 is an epoxy intumescent suitable for cellulosic fire protection which can be applied directly onto blast cleaned steel. It is an exterior durable intumescent, suitable for application in-shop and on site, provided the conditions specified in the product data sheet are adhered to.
Sherwin-Williams FIRETEX M95/02 is an epoxy intumescent suitable for cellulosic fire protection which can be applied directly onto blast cleaned steel. It is an exterior durable intumescent, suitable for application in-shop and on site, provided the conditions specified in the product data sheet are adhered to.
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Sherwin-Williams Firetex J120 is a high temperature fire resistant fabric scrim cloth, designed to reinforce the insulation ‘char’ developed when Firetex M90 reacts in a fire.
Jotun Steelmaster 600WF is specially designed as passive fire protection for steel constructions. Designed to protect up to 60 minutes on a wide range of I section beams and columns. Will provide 90 minutes fire duration as per BS476 part 20-21. Suitable for structural steel exposed to internal environments up to corrosivity category C3 (ISO...
International Interchar 1260 is a single component, borate, chlorine and APEO free, water borne intumescent coating designed for on-site application to interior exposed structural steel requiring protection from cellulosic fire.
Nullifire TS816 Water-Based Acrylic Top Seal is a waterborne, acrylic eggshell decorative topseal. It is primarily for use with Nullifire Intumescent Basecoats on internal steelwork.
Jotun Steelmaster 60WB is a one component waterborne acrylic thin film intumescent coating independently approved for fire protection of structural steel exposed to cellulosic fire. ADVANTAGES Best loadings for beams and columns Low VOC, water-borne Single coat application for a majority of 60minute steel sections Low odour Tested to...
Thermoguard Thermocoat W is a White Intumescent Paint for steel, structural steel and cast iron: Up to 90 minutes’ fire resistance Can be overcoated with compatible decorative topcoat Water-based Low odour Environmentally friendly Cost effective for large projects Certificate of supply available on request Can be applied by brush,...
Sherwin-Williams Firetex M72 is a solvent based intumescent mastic coating, used for the repair of small areas of mechanical damage to Firetex range of intumescent coatings.
Sherwin-Williams Firetex FX2003 is single pack thin film intumescent coating, designed for in-shop application by airless spray to provide fire resistance for up to 120 minutes on structural steel.
A one-component, thin-film solvent-borne intumescent coating for fire protection of circular and rectangular hollow section structural steel. Top Features Tested and assessed to EN 13381-8 CE marked product, ETA 15/0053 Assessed to ETAG 018-2 for all durability classifications
Sherwin-Williams Firetex FX5060 is a water-based TCEP free thin film intumescent coating. It has been designed for application by airless spray to provide fire resistance up to 60 minutes on structural steel.
Nu-Flame W Steel Basecoat is a thin film water-based decorative intumescent paint system providing fire resistance to structural steel and cast iron. Advantages Up to 90 mins fire resistance Water-based Safe for internal use 12-month shelf life
Sherwin-Williams Firetex J220 Scrim Cloth is a high temperature jet fire resistant fabric scrim cloth designed to reinforce the insulation ‘char’ developed when Firetex M90/02 reacts in a fire.
Thermoguard High Build Metal Primer is the compatible, corrosion-resistant primer recommended for use on suitably prepared steel prior to the application of Thermoguard Thermocoat W. ADVANTAGES High build Quick dry Corrosion resistant Water-based/Solvent-based Protects during construction
PPG Steelguard 2458 is a one-component, solvent-borne acrylic finish coat for SteelGuard intumescent coatings. Top Features Finish coat for SteelGuard intumescent coatings Good gloss and color retention Resistant to water and splash of mild chemicals
Sherwin-Williams FIRETEX FX9500 is a scrim free, epoxy intumescent coating suitable for cellulosic fire protection designed for extreme external environments. It is designed for application by airless spray to provide fire resistance for periods of up to 120 minutes on structural steel. It is an exterior durable intumescent, which can be applied directly...
Due to product development the manufacturer of this product have temporarily removed it from sale - We expect to see it return in August 2019. In the meantime we can recommend Zeroflame Aquasteel WB+ as a great alternative. Bollom Brosteel Ultra 60 is a White Intumescent Paint for structural steel members: Provides 30 and 60 minutes’ fire...
