RSL Resubind UV

RSBUB

This product is currently unavailable for order; please contact our technical team on 0113 2455450 (option 2) or [email protected] to discuss a suitable alternative.

Resubind UV is a light stable polyurethane binder product for use internally and externally. It provides a tough and durable surface for stone bound carpet systems. 

  • Catalysed and non-catalysed available
  • Works in a variety of thicknesses
  • Compatible with many stones/aggregates/substrates
  • User friendly
Colour
Size
Finish
Quantity

Description

This product is currently unavailable for order; please contact our technical team on 0113 2455450 (option 2) or [email protected] to discuss a suitable alternative.

Resubind UV is a very versatile system for use both domestically and industrially. It can also be tailored to your requirements - choose your thickness and control the speed of the cure by adding the catalyst during mixing. 

It has a low viscosity, has durable qualities, and can be used on a variety of decorative stones and aggregates.

RECOMMENDED USES

  • Automotive showrooms
  • Sports grounds
  • Play areas with rubber crumb
  • Balconies, decks and hallways
  • Domestic driveways and walkways
  • Architectural features


Resubind UV must be laid onto dry surfaces with a temperature of less than 7°C

Preparation

Internal New Floors: New concrete must be clean, sound and dry and fully cured with surface laitance removed, preferably by vacuum enclosed shot-blasting or mechanical grinding. A minimum strength of 25N/mm sq. is required. For substrates with moisture reading above 75% ERH or above, considerations should be given to the use of R.S. Dampshield as a barrier coat. Resuprime NT may be used on substrate with less than 75% ERH moisture content.

Existing Concrete Floors: Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing. Surfaces must be thoroughly rinsed and dried before application of Resubind UV finishes.

External Application: All surfaces must be clean, sound and dry at the time of application. Care must be taken to ensure that conditions remain suitable with no rain/condensation for the period of cure. The surface/substrate must be continuous and sound, and of a suitable composition to provide support to the laid surface.

Priming

Open and porous substrates may require priming with Resuprime NT, which may be used as primer on the dry substrates with less than 75% ERH reading.

Where the relative humidity of a substrate exceeds 75% ERH, R.S. Dampshield should be specified and selected on the basis of hygrometer readings, in accordance with BS 8203. The number of coats to be applied is chosen in accordance with the following table:

ERH% Required Coating Thickness
75-85 1coat of R.S.DAMPSHIELD at 200 microns per coat
85-92 2coats of R.S.DAMPSHIELD at 200 microns per coat
92-97 3coats of R.S.DAMPSHIELD at 200 microns per coat

For Further information please refer to recommended individual product data sheets.

Application

Ensure that all preparation and ground works are completed, and that a suitable surface remains that is both uniform in density and suitable for the application of the product. Edges/borders should be determined and any supporting battens fixed at the required height to allow for the correct placement of the mixed product.

Only once the site is completely ready, should the base resin and hardener be mixed (Note: This provides a mixed base with a long pot life >8 hrs. On larger jobs the mixed resin can then be added to the mixer with the catalyst, for non-catalysed version and aggregate). The base resin mix, catalyst solution and washed dried aggregates can then be added to the forced action mixer and stirred, to thoroughly wet out the aggregate. Normally 1.5 kg of resin is added to 25kg of 2-5mm aggregate.

Once mixed, the material should be placed swiftly and laid off by trowel, ensuring the product is well compacted and closed up on the surface.

NB: The degree of closure of the surface is dependent on the nature, shape and grading of the aggregate, and is often open textured. No solvents should be added to this product. On extended applications, tools should be kept clean with R.S. Polyurethane Solvent.

Product Details
RSBUB

Data sheet

Application
Trowel
Coverage
1.5 Kg to 25 Kg aggregate pack will cover 2m2 at 7mm thickness
Touch Dry
Once area is tack-free
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send