Teamac Antifouling D Plus

525/C258/4P/D

Teamac Antifouling D Plus discourages the growth of barnacles, weed, and other water life on the underwater areas of marine vessels. Contains a high level of cuprous oxide and a blend of biocides to give good antifouling performance.

  • Designed for vessels with a max speed of 25 to 30 knots
  • Excellent antifouling performance
  • Available in 5 colours
  • Expected functional life of the coating is 18 to 24 months
  • Suitable for domestic and commercial use
  • Works on steel, wood and GRP
  • H.S.E. Approval No. 7218
  • Click to jump down to Technical Data

Colour
  • Current colour: Blue
Choose a colour
Close colour picker
  • Black
  • Grey
  • Red
  • Green
  • Blue
Size
Finish
£34.17
VAT excluded

£41.00 Tax incl.
Quantity

Description

Teamac Antifouling D Plus is an antifouling coating for the underwater areas of marine vessels or underwater structures. Suitable for domestic and commercial vessels with steel, wood, or GRP hulls. Do not use on aluminium vessels.

Teamac Antifouling D Plus is a modified composition containing a high level of cuprous oxide to give good antifouling performance. Designed for vessels with a max speed of 25 to 30 knots. Expected functional life of the coating is 18 to 24 months. H.S.E. Approval No. 7218.

Click To Jump To Section:




Features & Benefits


  • Suitable for domestic and commercial vessels
  • Excellent Performance
  • Available in 5 colours
  • Designed for vessels with a max speed of 25 to 30 knots
  • Suitable for domestic and commercial use
  • Works on steel, wood and GRP
  • H.S.E. Approval No. 7218
  • Do not use on aluminium vessels



Product Specification


Technical Data
Volume Solids 57 - 60%
VOC Content 280 - 320 g/litre
Specific Gravity 1.45 - 1.65 @ 20°C
Finish Semi-gloss
Viscosity 4.5 Poise @ 25°C
Flash Point 38°C (closed cup)



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness Theoretical Coverage
Maximum 60 µm 100 µm 10 m2/litre. 60 microns dft. Based on brush or roller application.
The practical spreading rate may be lower as this depends on factors such as the porosity and roughness of the surface to be painted and material losses during application.



Drying Times


Drying Times At 20°C/RH 50%
Touch Dry: 3 Hours
Dry To Recoat: 16 Hours
Fully Cured: 18 Hours

Low temperature and high humidity will adversely affect application, drying and performance of any coating.



Surface Preparation


  • Do not use on aluminium vessels.

  • Bare Surfaces: On exposed metal and wood, prime first with at least 2 coats of Teamac Metaclor Underwater Primer (but not more than 3). On GRP lightly abrade exposed surfaces and apply 2 coats of Teamac Metaclor Underwater Primer.

  • New steel: Abrasive blast clean to Sa2½ and apply Teamac Metaclor Underwater Primer. If applying onto shop-primed steel ensure that surface is dry and clean, and areas of damaged primer are suitably cleaned prior to the application of the Teamac Metaclor Underwater Primer.

  • Maintenance: Remove all loose and damaged existing coating and all marine growth. High pressure wash with fresh water. Areas of breakdown should be blasted or power tool cleaned. Touch up with Teamac Metaclor Underwater Primer to the full existing film thickness. Prior to the application of the full coat ensure that surface is clean and free of all contaminates.



Mixing


Mix well before use.



Application Conditions


As dictated by normal good painting practice. Care must be taken during application that the temperature is above the dew point to avoid any contamination.



Application Methods


Method Airless Spray Conventional Spray Brush Roller
  Yes No Yes Yes



  • Always apply at least 2 coats of Teamac Antifouling D Plus
  • APPLICATION BY SPRAY IS ONLY PERMITTED BY PROFESSIONALS. AMATEUR USE MUST BE BY BRUSH OR ROLLER.
  • Nozzle Size: 0.017" - 0.021"
  • Thinners (Max vol): Thinners 17 (5%)



Health & Safety


Users must comply fully with all their legal responsibilities under the Control of Pesticides Regulations 1986 (as amended), including complying with all conditions of approval. H.S.E. Approval No 7218. Launch time after painting - minimum 8 hours, maximum 3 months if shrouded from direct sunlight. Minimum 2 coats

See safety data sheet - Red - SDS 10417, All other colours SDS 10489

Click to go back to the top of the page

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
525/C258/4P/D

Data sheet

For Use On
Steel, Wood, GRP
Application Method
Brush, Roller, Spray
Sheen
Semi-Gloss
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Single
Product Certifications
H.S.E. Approval No. 7218
Pack Size
1L, 2.5L, 5L
Application
Brush, Roller, Spray
Dry to Recoat (at 20°C)
16 Hours
Coverage
10m² per litre
Recommended Thinner/Cleaner
Thinners 17
Solids by Volume
57 - 60%
VOC
280 - 320 g / litre
Touch Dry
3 Hours
Finish
Semi-gloss
Size
1 litre, 2.5 litre, 5 litre
Recommended Dry Film Thickness
60
Recommended Wet Film Thickness
100
UN Number
UN1263
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send