Axalta ViterLac DTM190 Primer/Finish is a one coat anti-corrosive alkyd primer/finish (gloss) for the ACE market. Fast drying single coat system for blast cleaned steelwork for in-shop application.
Provides a colourful high gloss finish from one fast drying in-shop application
Specially designed for the ACE market
Available in a wide colour range
For blast-cleaned steelwork
Hard Dry in approximately 16hrs at 23°C
Wide colour range of RAL and BS shades
Designed for airless spray application
Excellent build properties and hold-up on edges
Resistant to splashes of diesel and hydraulic fluid (see Product Notes)
Please Note: Colours tinted on a White base are only available in a 5L pack size. When using the colour picker, Price Bands 1 and 2 will show colours tinted on a White base, Price Bands 3 and 4 are for all other tintable colours
Please note:Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Axalta ViterLac DTM190 Primer/Finish is a one coat anti-corrosive alkyd primer/finish (gloss) for the ACE market. Fast drying single coat system for blast cleaned steelwork for in-shop application.
It is designed for airless spray application, and it has excellent build properties and hold-up on edges.
Axalta ViterLac DTM190 provides a colourful, high gloss system in one coat*.
*Colours such as yellows, reds and oranges have lower opacity, especially when produced using lead-free pigments. Two or three coats of these shades may be required, relative to only one coat of a grey or red oxide, so that yellows, bright reds and oranges may not be suitable as one coat systems.
Approvals/Certification - Please consult Axalta Coating Systems or Rawlins Paints Technical on 0113 2455450 (option 2) or send a message to [email protected].
Only apply in conditions of good ventilation which must be maintained during drying and curing
Do not apply when rain, mist, sleet or snow are imminent
During application and drying time of the paint coating, the surface should be dry, the relative humidity should not exceed 85% and the steel temperature should remain at least 3°C above the dew point
Paint temperature should ideally be at a minimum of 15ºC
Application Methods
Airless Spray: Output fluid pressure at tip 2000-2500 psi, Tip Size 11-13 thou (0.28-0.33 mm)
Conventional spray: typical atomising pressure 40-60 psi, will require thinning to 23-35 seconds at 25ºC through a BS B4 Flow Cup. Multiple coats will be required to achieve recommended dft
Application by brush/roller will result in a reduced film thickness and is recommended only for small areas of touch up/remedial work
Product Notes
Damaged areas may be touched up after the minimum times shown. Can be overcoated with itself indefinitely if clean and sound
In common with most alkyd primers and primer/finishes, this product is not recommended for extended exterior exposure, exposure in aggressive or coastal locations, or for immersion. Epoxy primers are preferred for these conditions, please consult Axalta Coating Systems or Rawlins Paints Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for advice.
When fully cured, ViterLac DTM190 resists splashes of diesel oil and hydraulic fluid. Splashes of petrol and brake fluid may cause some softening and loss of gloss. Splashes should be immediately removed to prevent long term film damage
Some shades may contain lead based colourants and these are labelled (L)
*Colours such as yellows, reds and oranges have lower opacity, especially when produced using lead-free pigments. Two or three coats of these shades may be required, relative to only one coat of a grey or red oxide, so that yellows, bright reds and oranges may not be suitable as one coat systems
Health & Safety
Containers are provided with safety labels which should be observed
Further information about hazardous influences and protection are detailed in individual Product Safety Data Sheets
For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Axalta ViterLac DTM190 Primer/Finish is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
Axalta 1006 Thinner, for use with the Axalta range of coatings has a specially formulated blend of solvents designed to mix with its compatible paint/coating to create an optimal consistency for application whether it be for brush, roller or spray. Can also be used for the cleaning of some surfaces prior to application of the coating...