We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product. See our metal paints page for more RSL paints and coatings.
Resuprime ZP is a two-pack, high solids epoxy resin zinc phosphate primer coat, designed for easy application, with good surface wetting properties. Resuprime ZP is principally designed to bond thin section resin based screeds and toppings to steel and ferrous structures, and is recommended for use as an anti-corrosion primer for Sherwin-Williams flooring products and on mezzanine areas, bridge decks, loading bays, ramps and stairs.
| Information & Data | |
|---|---|
| Product Information | |
| Finish | Smooth gloss |
| System Thickness (Recommended) | 200-250 microns WFT 184-230 microns DFT |
| *The suggested thickness range is calculated based on average volume solid as a general recommendation for the specified condition and for each application may vary. | |
| Solids Content by Weight | 94% |
| Solids Content by Volume | 92% |
| Pack Make Up | 1 x Base 1 x Hardener |
| Shelf Life | 36 months (Base & Hardener) |
| Storage | Keep out of direct sunlight. Store in a dry place, between 15°C and 30°C. |
| Application Information (at 20°C) | |
| Coverage Rate (Theoretical) | 5 kg will cover 18m² at 200 microns WFT |
| * Coverage rate is calculated based on a sealed and smooth surface and may vary based on the substrate roughness and other conditions. | |
| Pot Life | 30 minutes |
| Recoating Intervals | 6-8 hours or once surface has lost tackiness |
| Light Traffic | 6-8 hours |
| Full Traffic | 24-36 hours |
| Full Chemical Cure | 7 days |
| Technical Information | |
| The following figures are obtained from laboratory tests and RSL's experience with this product. | |
| Temperature Resistance | Tolerant of temperatures up to 60°c |
| VOC | 80 g/l calculated per full mixed unit |
| Life Expectancy | Dependant on floor system. |
All surfaces should be thoroughly cleaned to remove all contaminants oils and grease, ideally shot-blasted to SA 2.5 or better (Bright Steel), or mechanically abraded to remove all rust, mill scale, loose or flaky paint.
Compatibility tests should be undertaken prior to over-coating existing paint, for further information please consult Sherwin-Williams Technical Department or Rawlins Paints Technical on 0113 2455450 (option 2) or [email protected].
The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 10°C.
Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally to allow the ambient and substrate temperature to stabilise prior to installation. Mix the entire contents of the base with the hardener. If a separate mixing bucket is being used mix thoroughly ensuring all contents of both components are removed from the buckets supplied. Mix using a slow speed electric mixer for approximately two minutes or until the two components have fully combined.
The mixed unit should be applied immediately by roller or brush with a consistent procedure. Floor areas should be cross-rolled to ensure even application and to minimise roller marks.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
RSL Resuprime ZP is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...
£25.84 (incl. VAT)
£21.53 (ex. VAT)
