Rust-Oleum 2990 Stain Blocker
  • Rust-Oleum 2990 Stain Blocker

Rust-Oleum Hard Hat 2990 Stain Blocker

2990

Rust-Oleum Hard Hat 2990 Stain Blocker is a matt white high-pigmented coating for the permanent isolation of problem stains from nicotine, soot, tar, rust, the effects of moisture, graffiti, and numerous other colourings. 

  • Matt white finish, best possible opacity (Non-yellowing)
  • For application on concrete, plaster, particle board existing coatings, wall paper etc.
  • Odourless. Recoatable with standard wall paints

Colour
Size
Finish
£5.91
VAT excluded

£7.09 Tax incl.
Quantity

Description

Rust-Oleum Hard Hat 2990 Stain Blocker

Rust-Oleum Hard Hat 2990 Stain Blocker is a matt white high-pigmented coating for the permanent isolation of problem stains from nicotine, soot, tar, rust, the effects of moisture, graffiti, and numerous other colourings.

Rust-Oleum Hard Hat 2990 Stain Blocker is a renovation paint which can be applied directly on ceilings, plaster, cement, wood, concrete, wallpaper, isolation walls, old paints, etc. Rust-Oleum Hard Hat 2990 Stain Blocker can be used as a topcoat or can be recoated with standard paint.

Features & Benefits

  • Matt white finish, best possible hiding power
  • Masks stains from nicotine, soot, moisture, etc.
  • For use on ceilings, walls, wood, etc.
  • Non-yellowing and odourless
  • To recoat with standard wall paints
  • For use on concrete, plaster, particle board, etc.
  • Touch dry after just 5-10 minutes

Technical Data

  • Gloss Level: Matt
  • Propellant: Propane/Butane

Drying Times At 20°C/RH 50%

  • Touch dry: 5 minutes
  • Dry to recoat: Wet in wet / after ½ hour
  • Fully cured: 24 hours

Surface Preparation
Remove dirt, grease, oil, loose rust and all other surface contaminants by appropriate means. Sand intact coatings to roughen the surface slightly. The surface must be clean and dry during application.

Directions for Use
Remove cover cap. Shake vigorously for at least one minute after the rattle of mixing ball is heard. Shake frequently during use. Hold can approx. 25cm from surface. Use back and forth motion keeping can parallel with surface. Ensure that can is in motion when spray button is pressed to avoid runs and sags. Apply several thin layers at a few minutes interval to achieve adequate coating thickness. After use turn can upside down and press spray button for 2 - 3 seconds to clean valve.

Application Conditions
For optimum results the relative humidity should be below 85% and the temperature of the can above 0°C.

Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
2990

Data sheet

Application
Spray
Dry to Recoat (at 20°C)
Wet in wet / after ½ hour
Fully Cured (at 20°C)
24 Hours
Coverage
2.1m² per can
Min. Application Temperature
0°C
VOC
538 g/l
Touch Dry
5-10 Minutes
UN Number
UN 1950
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send