

We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.
Please note that this product is only available with a minimum purchase of 300 litres; for smaller quantities we recommend Sherwin-Williams Acrolon 1850 as a good alternative.
Sherwin-Williams Acrolon C750V2 (formerly known as Leighs C750V2) is an isocyanate free, two-pack finish coat for exterior exposed surfaces where retention of gloss is required, and the use of isocyanate products is precluded or undesirable. Sherwin-Williams Acrolon C750V2 is normally used in conjunction with epoxy primers and undercoats and is Highways Agency and Network Rail approved.
Compatible with a wide range of Macropoxy, Dura-plate, Zinc Clad Epoxy Primers and Buildcoats. Acrolon C750V2 must be applied over epoxy materials within 4 days at 23°C to ensure satisfactory intercoat adhesion.
This material should preferably be applied at temperatures in excess of 10ºC. In conditions of high relative humidity, ie 80-85% good ventilation conditions are essential. Substrate temperature shall be at least 3ºC above the dew point and always above 0°C. At application temperatures below 10°C, drying and curing times will be signifi cantly extended, and spraying characteristics may be impaired. Application at ambient air temperatures below 5°C is not recommended.
Steelwork coated with Acrolon C750V2 Special Finish should be protected from weather for 48-72 hours after application, depending on conditions. Consult our Technical Team if in doubt.
Drying times, curing times and pot life should be considered as a guide only. The curing reaction of the material commences immediately the two components are mixed, and since the reaction is dependent on temperature, the curing time and pot life will be approximately halved by a 10°C increase in temperature and doubled by a 10°C decrease in temperature.
Tropical Use
Acrolon C750V2 at the time of mixing should not exceed a temperature of 35°C. Use of this product outside its pot life may result in inferior adhesion properties even if the material appears fit for application. Thinning the mixed product will not alleviate this problem.
It is not advisable to apply this coating when the air and substrate temperatures exceed 45°C. These conditions can introduce paint film formation defects, such as dry spray, bubbling and pinholing etc. Numerical values quoted for physical data may vary slightly from batch to batch.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
![]() | Question: metal-paints/metal-topcoats/1932-sherwin-williams-acrolon-c750v2 Can this be made in BS 381C 175 Light French blue? |
Answer: Yes, you can order this with us via telephone on 0113 2455450. | |
• These colour samples are to be used for guidance only.
• Product contained within is generic to provide a close representation to your chosen colour.
• Should not be used to carry out any painting project, this is for colour selection purposes only and does not remove the need for you to ensure the correct product is chosen and tested for your application once a colour has been decided on.
• It is not a sample of the product you intend to purchase/use and cannot be used to test anything other than colour appearance.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application, batches variances number of coats and substrate surface.
• We cannot therefore promise that the colour of the product you ultimately purchase will exactly match the colour of this colour sample.
• Once you have selected a colour, you must purchase the smallest amount of the product you intend to use in your chosen colour and apply to a small, inconspicuous test area to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application and product surface.
• We cannot therefore promise that the colour of the product you paint with the Kolorbond paint will exactly match the colour of the item you send to us.
• You must therefore purchase the smallest Kolorbond paint pot available first and then apply the paint to a small, and where possible hidden, test area of your product to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint to your product if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.