

We no longer stock this product, but can recommend Nullifire FR230 Intucompound Fire Mortar as a great alternative.
Nullifire FR220 Firestopping Compound is a single part gypsum-based compound providing up to 4 hours fire resistance. FR220 Firestopping Compound provides an effective barrier to the spread of smoke and fire resistance tested in accordance with EN 1366-3, ETAG 026 and Classiffcation 13501:2.
FR220 Firestopping Compound is used to stop the spread of smoke and fire along services that pass through compartment walls and floors, whilst providing an unsupported load bearing capacity. The system also provides thermal, acoustic and air sealing performance.
FR220 is suitable for the following service penetrations; single and bunched cables, cable trays, cable ladders, trunking, steel and copper pipes, unsupported multiple ducting/ damper penetrations, PVC and uPVC pipes. Typical areas of use include health and leisure facilities, schools, universities, commercial. retail and industrial buildings.
For spans greater than 700 mm or parameters outside the scope as detailed in the TDS including seals that require a UDL in excess of 2.5 kN/ m², please contact our Technical Team for advice.
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions and should be applied only by an individual with the necessary expertise and experience. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.
![]() | Question:
Would this product be used to seal joints/inside and outside corners of 60min 15mm gyproc fire board, to seal fire board around structural steel posts? If Yes what is the drying time, can it be decorated over and what is the coverage of a 20kg bag. |
Answer:
Generally we propose the use of Nullifire FB750 Coated Batt for primary seals or Nullifire FS702 Waterborne Intumescent Acrylic Sealant for linear gaps. | |
![]() | Question: Would you use this Product to cement Fire bricks in a Fire pit regards Mark |
Answer: No, unfortunately the product was not designed or tested for this. | |
• These colour samples are to be used for guidance only.
• Product contained within is generic to provide a close representation to your chosen colour.
• Should not be used to carry out any painting project, this is for colour selection purposes only and does not remove the need for you to ensure the correct product is chosen and tested for your application once a colour has been decided on.
• It is not a sample of the product you intend to purchase/use and cannot be used to test anything other than colour appearance.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application, batches variances number of coats and substrate surface.
• We cannot therefore promise that the colour of the product you ultimately purchase will exactly match the colour of this colour sample.
• Once you have selected a colour, you must purchase the smallest amount of the product you intend to use in your chosen colour and apply to a small, inconspicuous test area to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application and product surface.
• We cannot therefore promise that the colour of the product you paint with the Kolorbond paint will exactly match the colour of the item you send to us.
• You must therefore purchase the smallest Kolorbond paint pot available first and then apply the paint to a small, and where possible hidden, test area of your product to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint to your product if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.