Teamac High Performance Polyurethane Topcoat (previously known as Teamac P101 High Performance Finish and Teamac High Performance Marine Gloss) is an aliphatic, 2 pack polyurethane topcoat that is light stable so will not fade or yellow when exposed to high levels of ultra violet light.
Professional use only - from the 24th August 2023, adequate training is required before industrial or professional use of this product.
Should you require training, visit - https://www.safeusediisocyanates.eu/
Professional use only - from the 24th August 2023, adequate training is required before industrial or professional use of this product.
Should you require training, visit - https://www.safeusediisocyanates.eu/
Teamac High Performance Polyurethane Topcoat (previously known as Teamac P101 High Performance Finish and Teamac High Performance Marine Gloss) is an aliphatic, 2 pack polyurethane topcoat that is light stable so will not fade or yellow when exposed to high levels of ultra violet light. It is used as a coating that will not support fungus growth and is easily cleaned of surface contaminants. Ideal for marine applications on GRP, wood, ferro concrete and suitably primed metals. It can be used over compatible water based paints but is not recommended for use over conventional single pack solvent based paints.
| Technical Data | |
|---|---|
| Volume Solids | 47% |
| VOC Content | Max 498 g/litre |
| SG | 1.07 @ 20°C |
| Viscostity | N/A |
| Flash Point | 40°C (closed cup) |
| Product Data | |||
|---|---|---|---|
| Dry Film Thickness | Wet Film Thickness | Theoretical Coverage | |
| Maximum | 55 to 65 µm | 120 to 135 µm | 7.5 to 8.5 m2/litre @ 75 microns D.F.T |
The practical spreading rate may be lower as this depends on factors such as the porosity and roughness of the surface to be painted and material losses during application.
| Drying Times At 20°C/RH 50% | |
|---|---|
| Touch Dry: | 3 - 4 hours |
| Dry To Handle: | 16 - 24 hours |
| Dry To Recoat: | 16 hours |
| Fully Cured: | 5 - 7 days |
Low temperature and high humidity will adversely affect application, drying and performance of any coating.
Preceeding Coat
The product is supplied in two containers: one larger than the other and labelled Base. The other smaller one labelled Hardener. The contents of the pack marked Hardener are added to the contents of the larger pack marked Base and thoroughly mixed together, preferably by slow speed electric mixer for 2 minutes or until thoroughly mixed. Failure to mix the material correctly will lead to uncured areas in the coating.
| Method | Airless Spray | Conventional Spray | Brush | Roller |
|---|---|---|---|---|
| Yes | No | Yes | Yes |
For clear hardener see safety data sheet - SDS 10866, for base see safety data sheet - SDS 10867. For all colours hardener see safety data sheet - SDS 10973, for base see safety data sheet - SDS 10972.
Click to go back to the top of the page
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
 Geoffrey Home on 2024-02-26 22:03:20 | Question: We will not be using the entire 1 litre in one go. What is the mixing ratio please? |
Answer from Rawlins’ Technical Team: It is not recommended to part mix this product, the manufacturer does not list the mixing ratio. | |
| steve field on 2022-06-11 08:59:03 | Question: Hi, would like to use your marine 2 part paint on my hull which has I assume standard marine enamel paint on it. Can this be primed and by what to enable me to use P101. |
Answer from Rawlins’ Technical Team: We would not recommend application of this product over a single pack enamel paint, this should be removed prior to application and an appropriate primer maybe required. Please provide more infomration to [email protected] | |
| Stuart on 2022-04-13 10:43:16 | Question: Hi, I’m considering using this product to coat nylon fabric on a skin -on-frame kayak. Required to be abrasion resistant, UV resistant and flexible. Any past experience or comments? |
Answer from Rawlins’ Technical Team: This product would not be suitable for this application unfortunately. | |
| Richard Mortlock on 2018-11-25 15:29:05 | Question: Can this product be used to seal crazed gelcoat on a dinghy deck ? Will it penetrate and bind to the grp substrate ? Is a primer needed ? The cracks are not hairline but are not wide. They are too extensive to consider re gelcoating. Thank you. |
Answer from Rawlins’ Technical Team: Assuming the crazing is not deeper than 1mm, we have customers that have success with the following system. If crazing is deeper than 1mm then you would need to re-gelcoat. Thoroughly clean all surfaces and apply Teamac 2 Pack Zinc Phosphate Primer to the crazes and allow to dry overnight. Sand, then clean down and apply a further coat of Teamac 2 Pack Zinc Phosphate Primer, sand again once dry and then apply 2 coats to all areas of Teamac P101 High Performance Finish in the desired colour. | |
Teamac High Performance Polyurethane Topcoat is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Teamac 2 Pack Zinc Phosphate Primer, is a two pack, high performing epoxy zinc phosphate primer for application to steel which is clean and free from scale and/or rust.For application to blast cleaned and other suitably prepared steel surfaces Dry to recoat in as little as 2 - 4 hours Up to 12 square metres per litre coverage Not...
£27.56 (incl. VAT)
£22.97 (ex. VAT)
General Painting Application Kit from Rawlins Paints provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site.Provides an economical way of making sure you will have what you need Ideal for interior and exterior paint projects Click to jump down to...
£12.04 (incl. VAT)
£10.03 (ex. VAT)
