RSL Resutop FH
  • RSL Resutop FH
  • RSL Resutop FH

RSL Resutop FH

TOFHB

Resutop FH is a fast curing, two-pack epoxy resin coating in one application that creates a seamless finish when chemical, abrasion, and impact resistance flooring is essential. 

ADVANTAGES

  • Recoat period of 4 hours at 20°C
  • Non-toxic and solvent-free
  • Good light reflection
  • Good colour stability
  • No shrinkage on curing
  • Easy to clean
  • Anti-slip is available

**Available for delivery - see Delivery Options below**

Colour
  • Current colour: White
Choose a colour
Close colour picker
  • White
  • Black
  • Magnolia
  • Salsa Red
  • Stirling Grey
  • Flint Grey
  • Buff
  • Savannah Yellow
Size
Finish
£82.37
VAT excluded

£98.84 Tax incl.
Quantity

Description

Resutop FH has an ultra-fast re-coat time and is applicable to all hard-wearing industrial sites. It is decorative, ideal for maintenance as is unaffected by powerful detergents, can be regularly disinfected or sterilised, and has excellent abrasion qualities. Anti-slip aggregates can be added to this smooth gloss finish system to improve and maintain safety underfoot.

Resutop FH comes in a range of colours for a coat that suits your needs, and is ideal for food processing, preparation and storage areas such as large kitchens. It is also very popular in aviation and automotive environments that can be impacted by heavy traffic.

Recommended Uses

  • Warehouse floors
  • Factory units
  • Engineering 
  • Car showrooms
  • Plane hangars
  • Airports 
  • Prisons

Preparation

New Concrete Floors: New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm sq. is required.

Existing Concrete Floors: Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue of detergent is washed and removed by rinsing with clean water. Local repairs should be carried out using Resuscreed PA or Resuscreed 45.

Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with existing floor coating.

Where Resutop FH is applied to masonry/concrete surfaces, care must be taken to ensure that surface preparation is thorough but does not disfigure the surface.

Priming

Open and porous substrates may require priming with Resuseal WB, also Resuprime MVT may be used as primer on the dry substrates only with less than 75% ERH reading.

Where the relative humidity of a substrate exceeds 75% ERH, Resuprime MVT should be specified and selected on the basis of hygrometer readings, in accordance with BS 8203.

The number of coats to be applied is chosen in accordance with the following table:

ERH% Required Coating Thickness
75-85 1coat of Resuprime MVT at 200 microns per coat
85-92 2coats of Resuprime MVT at 200 microns per coat
92-97 3coats of Resuprime MVT at 200 microns per coat

For Further information please refer to recommended individual product data sheets.

Application

The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 10°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally to allow the ambient and substrate temperature to stabilise prior to installation.

Mixing: Pre-mix the coloured base component to a uniform consistency then mix the entire contents of the base with the hardener. If a separate mixing bucket is being used mix thoroughly ensuring all contents of both components are removed from the buckets supplied. Mix using a slow speed electric mixer for approximately two to three minutes until the two components have fully combined.

The mixed unit should be applied immediately by squeegee, roller or brush with a consistent procedure. Floor areas should be cross-rolled to ensure even application and to minimise roller marks. Coverage rates may vary depending on profile and porosity of the substrate.

Product Details
TOFHB

Data sheet

Application
Brush, Roller, Squeegee.
Coverage
5Kg. will cover 19m sq. @ 200 microns wet film thickness.
Touch Dry
3-4 Hours
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

RSL Resuseal WB

Resuseal WB is a multi-purpose, two-pack, water-based epoxy coating primarily for concrete walls and floors. It can also be applied to concrete poured 7 days prior, as well as wood for a dust-free finish.  Low odour  Silica Free  Superb adhesion  Hard wearing  Hygienic Dust-free Some product colours are made to order and have minimum...

Price £50.53
In stock

RSL Resuscreed 45

Resuscreed 45 is a heavy duty, epoxy resin floor screed which uses a crystalline silica free aggregate, making it more environmentally friendly. Must seal for an impervious finish. ADVANTAGES Less dust than other screeds Low odour Hard wearing Abrasion and impact resistant Can form coving and falls Can be feather edged Can act as a...

Price £59.30
In stock

RSL Resuprime MVT

RSL Resuprime MVT (formerly known as R.S. Dampshield FH) is a faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood.  Features and Benefits:...

Price £19.80
In stock

RSL Resuscreed PA

RSL Resuscreed PA (formerly known as Resupatch) is a three-pack epoxy resin mortar designed for rapid concrete repair in heavy duty environments. Features and Benefits:  Excellent mechanical properties Can be feather edged Abrasion and impact resistant Dust-free Concrete like in appearance Easy to apply Minimum surface preparation...

Price £38.44
In stock