Rust-Oleum Thinner 160 is a specially formulated blend of solvents designed to mix with Rust-Oleum's 1085 Galva Zinc, 9100 High Performance Epoxy and B95 Flexible Epoxy to create an optimal consistency for application whether it be for Brush, Roller or Spray. Can also be used for the cleaning of some surfaces or equipment. Strong dilution...
Rust-Oleum 5421 Epoxy Floor Primer Rapid
Rust-Oleum 5421 Epoxy Floor Primer Rapid is a fast curing primer for use on new or untreated porous mineral surfaces, like concrete to bind weak and friable substrates - can be overcoated with any Rust-Oleum Mathys epoxy floor paint or polyurethane coating.
- Overcoatable after just 4 hours: apply primer and topcoat in one day
- Easy all-in-1 packaging
- Impregnates porous and brittle floors
- Very low solvent content
Rust-Oleum 5421 Epoxy Floor Primer Rapid
Rust-Oleum 5421 Epoxy Floor Primer Rapid is a rapid curing 2-component solvent-free epoxy impregnation primer for concrete floors.
Rust-Oleum 5421 Epoxy Floor Primer Rapid has excellent penetration properties and binds weak and friable surfaces. The recoating time of only 4 hours allows application of primer and topcoat in one day and it's high layer thickness makes it ideal for uneven surfaces.
Rust-Oleum 5421 Epoxy Floor Primer Rapid is for use on new or untreated porous mineral surfaces, like concrete. It can be used in combination with other epoxy floor paints and polyurethane coatings.
Features & Benefits
- Improves adhesion
- 100% solids
- Binds brittle surfaces
- Low odour
- Rapid curing
- High layer thickness
- Density: 1,1
- Gloss Level: Gloss
- Solids content in volume: 100 %
- Solids Content in weight: 100 %
- Mixing Ratio: Base : Activator = 3.3 : 1.7 (Volume)
Drying Times At 20°C/RH 50%
- Touch dry: 2 hours
- Dry to handle: 3 hours
- Dry to recoat: 4 hours
- Fully cured: 2 days
- Pot Life: 30 minutes (do not leave in mixing can)
Practical coverage depends on many factors such as porosity and roughness of the substrate and material losses during application.
New concrete should cure and dry for at least 30 days prior to the application of the product. Remove oil, grease and all other surface contaminations by alkaline or high pressure- (steam) cleaning in combination with appropriate detergents. Remove all laitance, loose or unsound concrete by vacuum-blasting or etching with Rust Surfa-Etch 108 Etching Solution. Remove concrete curing compounds completely. Large surfaces should preferably be prepared by abrasive blasting (vacuum blasting) or flame cleaning. Profile maximum 0,5 mm
Temperature of air and substrate between 10 and 35°C and relative humidity below 85%. The substrate temperature must be at least 3°C above dew point.
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Brush, Roller
- Dry to Handle (at 20°C)
- 3 Hours
- Dry to Recoat (at 20°C)
- 4 Hours
- Fully Cured (at 20°C)
- 2 Days
- 10m² per litre
- Solids by Volume
- 100 %
- Touch Dry
- 2 Hours
Be the first to ask a question about this product!
Sika Block Paving Seal is a low odour clear resin which impregnates and seals block paving, resisting oil and diesel spillage whilst improving the overall appearance of the paving blocks with a matt finish. Ideal for vehicle and pedestrian areas, new and existing drives, forecourts, parking areas, walkways and paths, etc. Features &...
Blackfriar Professional Water Based Floor Sealer is a clear, water-based, low-odour sealer. Ideal for binding, stabilising and sealing friable (loose) and porous surfaces prior to finishing with water-based coatings. Easy and safe to use. Product Features Specifically designed to seal bare and porous concrete substrates. Low-odour - ideal...
Sikafloor CureHard WW is a one part, sodium silicate based clear liquid for curing fresh concrete. This Sikafloor paint is suitable for concrete slabs where no specific curing efficiency or standards are required and can be used for interior or exterior applications. Features and Benefits: Ready to use Easy to apply Reduced risk of...
Remmers Epoxy Primer PF (formerly Epoxy Primer PF New) is a pigmented primer as well as base layer for blinded covers. Used as primer in the system Remmers Deck OS 8. Can be subjected to mechanical loads Excellent adhesion on concrete and cement screed Contains no plasticisers, nonylphenols or alkylphenols Physiologically harmless once...
Remmers Epoxy ST 100 is an unpigmented epoxy resin binder that is used as an impregnation agent, primer, bonding layer, levelling layer and for the production of compression resistant mortars, flow covers and as a blinding layer for blinded covers. Can be subjected to mechanical loads Can be subjected to chemical loads Good penetration...
RSL Resustat CP (formerly known as Resustat Primer) is designed to be applied prior to the use of Resustat ESM, Resustat SL23, Resustat TG69 or Resustat Terrazzo. It is a low viscosity epoxy primer with conductive fillers. Features and Benefits: Conductive with very low electrical resistance Good adhesion Low odour High solids Easy...
Remmers PUR Top Plus is a range of thin film polyurethane seal coats for synthetic resin coatings with exceptional scratch resistance. The products are available in three gloss levels, with the inclusion of a slip resistant bead finish. Used to impart a tough lacquered finish to resin floors to minimise scratching, impart specific matt/gloss...
Blackfriar Professional Oil Tolerant Primer is a specialist primer for surfaces with residual oil contamination. Ideal for concrete floors and screeds, promotes adhesion prior to coating with with Blackfriar Professional High Traffic Floor Paint. Product Details Designed for use over cleaned concrete floors and screeds. Tolerates all...
Smartkote Protectakote 2K Metal Primer is a dual component etch primer suitable for achieving adhesion of polyurethane to all types of aluminium as well as all other metal types where adhesion is problematic. Protectakote 2K Metal Primer is suitable for applications involving complete immersion in water.
Smartkote Protectakote Clear Primer Treatment is a single component primer treatment, which can be used to prepare inorganic surfaces for the subsequent adhesion of Smartkote polyurethane coatings. This product ensures excellent adhesion of reactive, solvent-borne urethanes to unreactive inorganic surfaces without changing their appearance....
Blackfriar Professional Epoxy Floor Primer is a low-odour, water-based primer that binds and stabilises friable and porous substrates prior to coating with Blackfriar Professional Epoxy Floor Paints. Product Details Water Based formula ensures low odour. Ideal for binding porous concrete surfaces prior to coating with Blackfriar...
Coo-Var Floor Sealer is a low cost, clear, semi-gloss sealer for suitably prepared concrete, wood, metal and GRP. A clear floor coating to help with the prevention of dusting. Product Features Low cost External/Internal use Semi-gloss Versatile Prevents dusting
Sikafloor 327 is a 2-part, tough, elastic polyurethane self-smoothing resin coating for indoor use in Decorative and Industrial flooring. It is solvent free, very low VOC emission and part of the Sika Comfort Floor Tough system. Features and Benefits: Very low VOC emission Solvent free Good mechanical resistance Easy to apply Easy to...