PPG Thinner 90-53
This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info
£42.59 (incl. VAT)
£35.49 (ex. VAT)
SigmaFast 205 LT, a two-component, high-build, polyamide-cured zinc phosphate epoxy primer/coating for atmospheric conditions, drying and curing at low temperatures down to –5°C (23°F).
SIGMAFAST™ 205 LT is a two-component, high-build, polyamide-cured zinc phosphate epoxy primer/coating available in 2000+ colours from RAL, NCS and British Standard. The general-purpose epoxy primer/coating is for atmospheric conditions, drying and curing at low temperatures down to –5°C (23°F), and is recoatable with most two-component epoxy and polyurethane coatings.
Reference | Colour | Size | Gloss Level |
---|---|---|---|
314463 | Light Grey (RAL 7035) | 20 litres | Semi-gloss |
317935 | Oxide Red (RAL 3009) | 20 litres | Semi-gloss |
317937 | Pure White (RAL 9010) | 20 litres | Semi-gloss |
317936 | Silver Grey (RAL 7001) | 20 litres | Semi-gloss |
320432 | Full RAL & BS | 4 litres | Semi-gloss |
320433 | Full RAL & BS | 20 litres | Semi-gloss |
Two-component, high-build, polyamide-cured zinc phosphate epoxy primer/coating.
Data for mixed product at 20°C (68°F) | |
---|---|
Number of components | Two |
Mass density | 1.4 kg/l (11.7 lb/US gal) |
Volume solids | 70 ± 2% |
VOC (Supplied) | Directive 1999/13/EC, SED: max. 213.0 g/kg |
UK PG 6/23(92) Appendix 3: max. 310.0 g/l (approx. 2.6 lb/US gal) | |
Recommended dry film thickness | 75 - 150 µm (3.0 - 6.0 mils) depending on system |
Theoretical spreading rate | 9.3 m²/l for 75 µm (374 ft²/US gal for 3.0 mils) |
4.7 m²/l for 150 µm (187 ft²/US gal for 6.0 mils) | |
Dry to touch | 3 hours |
Overcoating Interval | Minimum: 3 hours |
Maximum: 6 months | |
Full cure after | 5 days |
Shelf life | Base: at least 24 months when stored cool and dry |
Hardener: at least 24 months when stored cool and dry |
Notes:
Recommended Substrate Conditions and Temperatures
Substrate conditions
Substrate Temperature & Application Conditions
Instructions for Use
Mixing ratio by volume: base to hardener 75:25 (3:1)
Induction Time
None.
Air Spray
Recommended thinner
Volume of thinner
Nozzle orifice
Nozzle pressure
Airless Spray
Recommended thinner
Volume of thinner
Nozzle orifice
Nozzle pressure
Brush/roller
Recommended thinner
Volume of thinner
Cleaning Solvent
DFT | Theoretical spreading rate |
---|---|
75 µm (3.0 mils) | 9.3 m²/l (374 ft²/US gal) |
100 µm (4.0 mils) | 7.0 m²/l (281 ft²/US gal) |
150 µm (6.0 mils) | 4.7 m²/l (187 ft²/US gal) |
Overcoating interval for DFT up to 75 µm (3.0 mils)
Overcoating with... | Interval | -5°C (23°F) | 0°C (32°F) | 5°C (41°F) | 10°C (50°F) | 20°C (68°F) |
---|---|---|---|---|---|---|
Various two-pack epoxy and polyurethane coatings | Minimum | 22 hours | 16 hours | 5 hours | 3 hours | 2 hours |
Maximum | 6 months | 6 months | 6 months | 6 months | 6 months |
Notes:
Overcoating interval for DFT up to 150 µm (6.0 mils)
Overcoating with... | Interval | -5°C (23°F) | 0°C (32°F) | 5°C (41°F) | 10°C (50°F) | 20°C (68°F) |
---|---|---|---|---|---|---|
Various two-pack epoxy and polyurethane coatings | Minimum | 24 hours | 18 hours | 6 hours | 4 hours | 3 hours |
Maximum | 6 months | 6 months | 6 months | 6 months | 6 months |
Notes:
Curing time for DFT up to 75 µm (3.0 mils)
Substrate temperature | Dry to Touch | Dry to Handle | Full Cure |
---|---|---|---|
-5°C (23°F) | 18 hours | 21 hours | 20 days |
0°C (32°F) | 15 hours | 18 hours | 12 days |
5°C (41°F) | 4 hours | 7 hours | 6 days |
10°C (50°F) | 3 hours | 5 hours | 5 days |
20°C (68°F) | 2 hours | 3 hours | 48 hours |
Curing time for DFT up to 150 μm (6.0 mils)
Substrate temperature | Dry to Touch | Dry to Handle | Full Cure |
---|---|---|---|
-5°C (23°F) | 20 hours | 24 hours | 21 days |
0°C (32°F) | 16 hours | 20 hours | 14 days |
5°C (41°F) | 5 hours | 8 hours | 7 days |
10°C (50°F) | 4 hours | 6 hours | 6 days |
20°C (68°F) | 3 hours | 4 hours | 3 days |
Note:
Pot Life (at application viscosity)
Mixed product temperature | Pot life |
---|---|
10°C (50°F) | 6 hours |
20°C (68°F) | 4 hours |
30°C (86°F) | 1.5 hours |
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
PPG SigmaFast 205 LT is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info
£42.59 (incl. VAT)
£35.49 (ex. VAT)
This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info
£42.59 (incl. VAT)
£35.49 (ex. VAT)