Sherwin-Williams Epigrip M922
  • Sherwin-Williams Epigrip M922

Sherwin-Williams Macropoxy M922


Sherwin-Williams Macropoxy M922 (formerly Epigrip M922) is a high solids, 2-pack glass flake epoxy pigmented with micronised glass flake and anti-corrosives to provide anti-corrosive protection of blast cleaned steel and cathodically protected steel. Macropoxy M922 possess excellent abrasion resistance and has excellent resistance to immersion in sea water and a range of chemicals.

  • Current colour: Black
Choose a colour
Close colour picker
  • Black
  • Light Grey
  • Dark Grey
  • Off White
  • Red Oxide
  • Bright Yellow
VAT excluded

£107.50 Tax incl.


Sherwin-Williams Macropoxy M922 (formerly Epigrip M922) is a high solids, 2-pack glass flake epoxy pigmented with micronised glass flake and anti-corrosives to provide anti-corrosive protection of blast cleaned steel and cathodically protected steel.

Sherwin-Williams Macropoxy M922 possess excellent abrasion resistance and has excellent resistance to immersion in sea water and a range of chemicals. For immersed structures a suitable primer may be required. An aluminium mastic version is available for high build brushing maintenance - see Sherwin-Williams Macropoxy M922M.


  • Complies with BS5493:1977 - Table 4K -Type KP1A
  • Independently approved for Cathodic Disbondment to BGE/PS/CW6:Part 1
  • Approved to Def Stan 80-97 Treatment of Fuel Tanks
  • Highways Agency Item No. 123
  • Network Rail Item No. 7.2.3
  • Approved for carriage of grain
  • Complies with NORSOK M501 Rev. 5 System 7

Recommended Primers

Primers are optional. M922 can be applied directly onto steel.

  • Macropoxy M111 Wet Blast Primer
  • Macropoxy L574 Blast Primer

Recommended Topcoats

Indefinitely self overcoatable provided the coating has been suitably cleaned. For optimum intercoat adhesion with other epoxy topcoats, overcoating should occur within 14 days. Where atmospheric exposure is required overcoat with Acrolon C137V2, Acrolon C237, Acrolon 1850 and Acrolon 7300 within 7 days at a minimum d.f.t. of 50 microns or in the case of Acrolon C750V2 overcoat within 4 days.

These overcoating times refer to achievement of optimum adhesion at 23°C and will vary with temperature. 

For overcoating outside the above parameters and with alkyd systems, consult the Technical Department for advice.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details

Data sheet

Typical Coverage (per coat)
2.1m² per litre
Touch Dry
4 Hours
Brush, Spray

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

questions Ian Anderson  on 09/09/2018

Can Sherwin-Williams M922 be applied to very high temperatures on stainless Steel


The Sherwin-Williams Macropoxy M922 data sheet states 'Macropoxy M922 may be applied by brush onto hot surfaces up to 120°C. Multiple coats will be necessary to achieve required film build. Ensure good ventilation and adequate PPE due to rapid vapourisation of solvent from the film at high temperatures.' Preparation on stainless steel should be blasting with non-metallic abrasive to ensure an adequate blast profile.

Question about the product

* Required fields
16 other products in the same category:

Jotun Jotamastic 90 GF

Jotun Jotamastic 90 GF is a two component polyamine cured epoxy mastic coating that is a surface tolerant, abrasion resistant, high solids and high build. It is reinforced with glass flakes for improved abrasion and scratch resistance. Specially designed for areas where optimum surface preparation is not possible or desired.

Price £214.11
In stock

Carboline Carbothane 133 HB

A high build, low sheen finish that has excellent resistance to corrosion, chemicals and abrasion. Suitable for application over a number of Carboline primers and intermediates. Top Features Outstanding performance properties Suitable for application direct to inorganic zincs Application by spray, brush or roller

Price £70.88
In stock

Sherwin-Williams Dura-Plate 301S

Sherwin-Williams Dura-Plate 301S is an anticorrosive coating for long service life steel protection, normally used as an intermediate or topcoat as part of a 301 based coating system when very high edge retentive is required. It can be used for both immersion and above the waterline service in marine, offshore, construction and industrial applications.

Price £70.69
In stock

Rust-Oleum Mathys Noxyde

Rust-Oleum Mathys Noxyde is a water-based, single-component paint that offers 15 years of corrosion protection. ADVANTAGES Unrivalled corrosion protection and waterproofing Approved for corrosion class C5-M high (ISO 12944) Excellent edge coverage and protection of nuts, bolts & welds 200% elasticity - does not crack/peel when metal...

Price £43.08
In stock

Coo-Var Hammercote Hammered Finish

Coo-Var Hammercote Hammered Finish is a fast-drying coating which gives a hard, hammered gloss finish to metal objects. ADVANTAGES Direct to prepared metal or suitable primer Full hardness is reached after several days Very fast drying Also available in smooth finish Heat resistant up to 150°C 10 colours!

Price £17.70
In stock

PPG Dimetcote 9

PPG Dimetcote 9, an anticorrosive primer for structural steel that can withstand substrate temperatures from –90°C (–130°F) up to 400°C (750°F), with good resistance to impact and abrasion. 2 component anti-corrosion primer Moisture-curing zinc (ethyl) silicate coating for structural steel Withstands substrate temperatures from –90°C...

Price £270.50
In stock

Hydron Nu-Steel SP Anti-Corrosive Primer/Undercoat

Nu-Steel SP Anti Corrosive Primer/Undercoat is a high performance phosphate primer that is perfect for external metal structures that are exposed to the elements. Advantages High performance primer and undercoat. First class adhesion. 8-10m²/Litre average. 12-month shelf life.

Price £57.75
In stock

Hydron Nu-Steel SP Etch Primer

Nu-Steel SP Etch Primer is a single pack primer giving excellent adhesion to aluminium and other metal prior to subsequent paint systems. Advantages Available in Grey and Red Oxide. Excellent adhesion to metals. 12m²/Litre typical coverage. 12-month shelf life.

Price £57.75
In stock

Carboline Thermaline 4001

A single-component, high performance coating which has outstanding resistance to wet/dry cycling conditions at elevated temperatures. Top Features Prevents corrosion under insulation Aluminium and MiO reinforced inorganic film Continuous temperature resistance to 649°C Very good flexibility Self-priming; single component

Price £2,775.00
In stock

Carboline Carboglas 1601 SG

An extremely durable and chemically resistant cladding utilizes a multi-step curing process that incorporates chemically-fused glass flake reinforcing in a highly cross-linked polyester matrix. Top Features Outstanding marine exposure resistance Excellent resistance to both organic and mineral acids Outstanding long-term protection

Price £362.94
In stock

Carboline Polyclad 777 Medium-Set

A high performance 100% solids structural polyurethane designed to provide superior corrosion protection for steel, ductile iron and concrete pipe. Tenacious adhesion and high impact resistance allow its use in the harshest environments. Top Features Fast curing rate increases throughput Excellent abrasion resistance Compliant with AWWA...

In stock

Bradite Solar Reflective Bitumen

Confirming to BS 3416 and BS 6949, Type 1 Class A, this solar reflective bitumen coating is perfect for steel, non-ferrous metals, concrete, brick and asphalt, where a tough waterproof coating is required on surfaces. Advantages Hard-wearing gloss finish Repels water fast-drying High build coating

Price £58.19
In stock

Hydron Nu-Flame HB Metal Primer

Nu-Flame HB Metal Primer is ideal for priming cast iron and structural steel in preparation to apply the Nu-Flame Fire Retardant System for metals. Advantages Quick dry. Ideal for cast iron and structural steel. 8m²/Litre coverage. 3 colours available. 12-month shelf life.

Price £57.75
In stock

SikaCor 6630 High Solid

SikaCor 6630 High Solid is a versatile, high-build coating for steel and galvanizing, non-ferrous metals, plastic and timber. SikaCor 6630 High Solid is a low-solvent, oxidative drying high-build coating with active corrosion protection pigments based on modified synthetic resin combination.

Price £200.07
In stock

Carboline Carbothane 134 HP

A high-gloss and high-Solid polyurethane topcoat, which can be easily sprayed with conventional as well airless equipment. Top Features Excellent flexibility Excellent abrasion resistance Available in RAL colour shades VOC compliant

Price £310.50
In stock

Carboline Carbomastic 18 FC

This epoxy is a fast-curing, heavy-duty, high-build anti-corrosive coating with a broad and versatile list of uses in marine and other corrosive environments. It is an excellent choice for the protection of ship hull exteriors, underwater and ballast tanks. Top Features Excellent immersion performance in water Suitable as a rust...

Price £62.25
In stock