A high performance 100% solids structural polyurethane designed to provide superior corrosion protection for steel, ductile iron and concrete pipe. Tenacious adhesion and high impact resistance allow its use in the harshest environments. Top Features Fast curing rate increases throughput Excellent abrasion resistance Compliant with AWWA...
Carboline Carboguard 193
A high-Build zinc phosphate metal primer for new constructions and maintenance. Gives a good corrosion protection, excellent adhesion and increased application tolerance to a wide range of environmental conditions.
- Excellent corrosion protection
- Good chemical & abrasion resistance
- VOC compliant to current AIM regulations
Carboline Carboguard 193 is a High-Build zinc- phosphate primer for new constructions and maintenance. Gives a good corrosion protection, excellent adhesion and increased application tolerance to a wide range of environmental conditions.
Top Features & Benefits
- Excellent corrosion protection
- Good chemical resistance
- Good abrasion resistance
- VOC compliant to current AIM regulations
- Flat finish
Preparation & Application
Surfaces must be clean and dry. Employ adequate methods to remove dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating.
Sa2½ with a 25-50 micron surface profile. ST3 for Touch-up
SSPC-SP1 and sweep-blast according to Sa1
Previously Painted Surfaces
Lightly sand or abrade to roughen surface and degloss the surface. Existing paint must attain a minimum 3B rating accordance with ASTM D3359 “X-Scribe” adhesion test.
Power mix separately, then combine and power mix. DO NOT MIX PARTIAL KITS. Ratio 3:1 Ratio (A to B).
Spray: Up to 25% with Thinner 15.
Brush or Roller: Up to 12% with Thinner 33.
Use of thinners other than those supplied or recommended by Carboline may adversely affect product performance and void product warranty, whether expressed or implied.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
Be the first to ask a question about this product!
A high performance 100% solids structural polyurethane designed to provide superior corrosion protection for steel, ductile iron and concrete pipe. Top Features Fast curing rate increases throughput Excellent abrasion resistance Compliant with AWWA C222 Compliant with EN 10290 This product is available as POA. Click here to email us...
Carboline Plasite 4660 provides outstanding chemical resistance, abrasion and corrosion protection to a wide variety of steel and concrete substrates in aggressive environments at elevated temperatures. This product is available as POA. Click here to email us for more information. Top Features Solvent free Excellent chemical resistance...
A high performance pipe coating specially designed for the protection of pipeline interiors. Typical application could be pipeline interiors for water transmission. Top Features Fast curing rate increases throughput Superior wetting properties Meets AWWA C222 UL approved for ANSI/NSF Std. 61 potable water This product is available as...
A high performance tank lining with curing characteristics allowing the coating to be applied and cure at temperatures as low as 35°F (2°C) while achieving unmatched chemical resistance in caustic, acid, solvent and ethanol service. Formulated for use in a large variety of facilities including waste water, chemical and fuel storage, wet-gas...
A high solids modified epoxy cured with an amine adduct curing agent. Designed specifically as a highly chemical-resistant, non-toxic, tank lining. Top Features Excellent overall chemical resistance to a wide range of acids, alkalies and solvents Very good abrasion resistance and flexibility Complies with FDA 21 CFR 175,300 criteria for...
Thermo-Lag 3000-P is a petrochemical grade, 100% solids epoxy based intumescent designed to fireproof steelwork for up to a 4-hour fire rating, depending on the design. The recommended use for this product is fireproofing of steel beams, columns, tubes, pipes, vessel skirts, bulkheads, underdecks and electrical raceways. Top Features UL...
A water-resistant epoxy coating polymerized with a polyamine type curing agent. A high performance lining for elevated temperature and pressure immersion services in high purity water, as well as the oil/water separating processes encountered in the petroleum industry. This HAR version of Plasite 7159 is extremely abrasion resistant. Top...
PPG NovaGuard 4701 is a two-part glass flake vinylester primer for concrete and steel as a holding primer for Novaguard 4801. Suitable for service temperature >80°C (176°F) when overcoated with NOVAGUARD 4801 dependent on the actual environment. Mixing ratio by volume: base to catalyst 98:2
This product is now only available with a minimum order of 800 litres; for smaller orders, we can recommend Jotun Jotacote Universal N10 as a great alternative. Jotun Jotacote Universal is a two component amine cured pure epoxy coating that is a fast drying, abrasion resistant, high solids and high build. Designed as an universal, all round,...
This lining-grade epoxy has wide chemical resistance and is suitable for use as a chemically resistant coating for aggressive atmospheric exposures or as a lining for a variety of chemical exposures. It is suitable for use in food-grade service where product purity (taste and odour) are critical. This product is available as POA. Click here...
Zinga is a one-component anti-corrosion zinc coating system that provides cathodic protection to steel comparable with hot-dip galvanising, with the added advantage that it can be applied as though it were a paint, and is certified to not spread flame or create smoke (BS476 parts 6&7). Can protect longer than hot-dip galvanising (at the...
A highly chemical resistant epoxy mastic coating with exceptionally versatile uses in all steel and concrete industrial markets Top Features Excellent chemical resistance Surface tolerant characteristics Self-priming VOC compliant to current AIM regulations
Rust-Oleum Mathys Noxyde is a single pack, water-based elastomeric coating with unequaled corrosion protection designed for spraying, offering 15 years of protection with excellent waterproofing and elasticity. ADVANTAGES Unrivalled corrosion protection and waterproofing Approved for corrosion class C5-M high (ISO 12944) Excellent edge...
A heavy duty, high build coating for protection of steel in corrosive environments. Gives a hard and smooth surface with excellent flexibility. Top Features Excellent immersion performance in water. Suitable as a rust preventing coating in ballast tanks. Ideal for areas prone to condensation. Very good abrasion resistance.
Cromadex 280 One Pack Eggshell Primer Finish is a one pack eggshell primer finish suitable for both interior and exterior use. The product contains zinc phosphate giving added corrosion resistance for greater durability. It is a high build product making it suitable for application over shotblasted steel. Cromadex 280 is available in full Cromadex range...