PPG Thinner 20-05
This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info
£42.59 (incl. VAT)
£35.49 (ex. VAT)
We no longer stock this product, but can recommend International Intertuf 16 as a great alternative.
Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to discuss your project.
PPG Sigma Vikote 63 is a high-build bituminous protective coating for steel, concrete and fibre cement. Offering good resistance to sea and fresh water, PPG Sigma Vikote 63 can be used to protect void spaces, cofferdams, steelwork behind lining and pipes.
PPG Sigma Vikote 63 is a high-build bituminous protective coating for steel, concrete and fibre cement. Offering good resistant to sea and fresh water, PPG Sigma Vikote 63 can be used to protect void spaces, cofferdams, steelwork behind lining and pipes.
Recommended Substrate Conditions and Temperatures
Substrate Conditions
Substrate Temperature and Application Conditions
Instructions for Use
Stir well before use. The temperature of the paint should preferably be above 15°C (59°F), otherwise extra thinner may be required to obtain application viscosity. Adding too much thinner results in reduced sag resistance.
Adequate ventilation must be maintained during application and curing (please refer to INFORMATION SHEETS 1433 and 1434).
Air Spray
Recommended thinner: PPG Thinner 20-05
Volume of thinner: 5 - 10%, depending on required thickness and application conditions
Nozzle orifice: 2.0 – 3.0 mm (approx. 0.079 – 0.110 in)
Nozzle pressure: 0.3 - 0.4 MPa (approx. 3 - 4 bar; 44 - 58 p.s.i.)
Airless Spray
Recommended thinner: PPG Thinner 20-05
Volume of thinner: 0 - 5%, depending on required thickness and application conditions
Nozzle orifice: Approx. 0.58 mm (0.023 in)
Nozzle pressure: 12.0 - 15.0 MPa (approx. 120 - 150 bar; 1741 - 2176 p.s.i.)
Brush/Roller
Only for touch-up and spot repair
Recommended thinner: PPG Thinner 20-05
Volume of thinner: 0 – 5%
Cleaning Solvent
PPG Thinner 20-05
Safety Precautions
Data for Product at 20°C (68°F) | |||||
---|---|---|---|---|---|
Number of components | One | ||||
Mass density | 1.2 kg/l (10.0 lb/US gal) | ||||
Volume solids | 57 ± 2% | ||||
VOC (Supplied) | Directive 1999/13/EC, SED: max. 308.0 g/kg. max. 365.0 g/l (approx. 3.0 lb/US gal) | ||||
Recommended dry film thickness | 250 - 500 µm (10.0 - 20.0 mils) depending on system | ||||
Theoretical spreading rate | 2.3 m²/l for 250 µm (91 ft²/US gal for 10.0 mils) | ||||
Dry to touch | 6 hours | ||||
Overcoating interval | Minimum: 8 hours. Maximum: Unlimited | ||||
Shelf life | At least 24 months when stored cool and dry |
Spreading rate and film thickness | ||
---|---|---|
DFT | Theoretical spreading rate | |
250 µm (10.0 mils) | 2.3 m²/l (91 ft²/US gal) | |
500 µm (20.0 mils) | 1.1 m²/l (46 ft²/US gal) |
Curing time for up to 250 µm (10 mils) | |
---|---|
Substrate Temp. | Dry to touch |
5°C (41°F) | 8 hours |
20°C (68°F) | 6 hours |
30°C (86°F) | 4 hours |
40°C (104°F) | 3 hours |
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
PPG Sigma Vikote 63 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info
£42.59 (incl. VAT)
£35.49 (ex. VAT)
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...
£25.84 (incl. VAT)
£21.53 (ex. VAT)