Tintable primer with 6,700+ colours and a fast drying time for use in a wet on wet system when recoated with 2K Topcoats.
Selemix 7-413 2K Epoxy Primer is a tintable 2K Epoxy primer that can be used on a wide range of substrates. Its fast drying performance allows 7-413 Epoxy Primer to be used in a wet on wet system when recoated with 2K Topcoats.
For use on Steel, Cast Iron, Aluminium, Light Alloys, GRP & Previously Painted Surfaces.
It has good anticorrosive properties making it suitable for the finishing and protection of machinery, agricultural, construction and earthmoving equipment, containers, cabins, generators, storage units, machinery and signage and many other industrial painting applications.
Available in over 6,700+ RAL, RAL Metallic*, BS, NCS and Selemix TIC colours.
*Note: RAL Pearl colours shown are approximations only - matches will not be exact.
For Professional Use Only.
Apply only on a clean and dry surface with a temperature above the dew point to avoid condensation. In confined spaces, provide adequate ventilation during application and drying.
Steel (Blast Cleaned):
Steel/Cast Iron:
Galvanised Steel:
Phosphated Steel:
Aluminium and Light Alloys:
GRP:
Painted Surfaces:
Do not use over wash primers or 1K synthetic primers.
| Features | Conventional Spray | Air-Assisted Airless |
|---|---|---|
By Weight: 7-413 Primer (Tinted) 9-010/9-011 Hardener | 1000 200 250-300 | 1000 200 90-100 |
By Volume: 7-413 Primer (Tinted) 9-010/9-011 Hardener 1-410/1-400 Thinner | 3.5 1 1-1.6* (30-45%) | 3.5 1 0.5 (15%) |
| Viscosity (at 20°C): | 18-30 secs DIN4 (*according to expected film build ) | 30-35 secs DIN4 |
| Pot Life (at 20°C): | 6 hours | 6 hours |
Mixing Ratio:
Please Note: Refer to the Product Data Sheet for detailed information regarding mixing ratios for the relevant binder/base and hardener/activator used.
| Features | Conventional Spray | Airless Spray |
|---|---|---|
| Spraygun Setup: | Nozzle: Gravity: 1.6-1.8mm Suction: 1.8-2.0mm Pressure feed: 1.2-1.4mm | Nozzle: 13-15 thou 0.33-0.38mm |
| Air Pressure: | HVLP: 2 Bar Standard: 2.5-3 Bar | 2.5 Bar |
| Fluid Pressure: | N/A | 100-120 Bar |
| Number of coats: | 2 | 2 |
| Flash-off between coats: | 10-15 mins | 10-15 mins |
| Drying: | Air dry 2 hours at 20°C or bake at 60°C for 50-60 mins | Air dry 2 hours at 20°C or bake at 60°C for 50-60 mins |
| Flash-off before bake: | 10-15 mins | 10-15 mins |
| Wet Film Thickness: | 100-200 microns | 100-200 microns |
| Dry Film Thickness: | 40-80 microns | 40-80 microns |
Please see the Product Data Sheet for detailed Application Instructions before use.
Note: Please see the Product Data Sheet for detailed information.
| Drying Times 20°C | |
|---|---|
| Dust Free | 20-30 mins |
| Handleable | 6-8 hours |
| Hard Dry | 24 Hours |
| Stoving | 50-60 minutes @60°C (according to film thickness) |
| Overcoating time | Minimum: 2 hours Maximum: 3 weeks without sanding on clean surface with any 2K Selemix Topcoat Before recoating for Selemix 7-540 Basecoat, primer must be air dried for at least 16 hours, or baked |
| Please Note: Lower temperature or film thickness higher than 80µm will extend drying times | |
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Selemix 7-413 2K Epoxy Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
For use with selected products in the Selemix range including Selemix 7-410 2K Epoxy Topcoat. Please see the Product Data Sheet for the Base Product for mixing ratios/application instructions before use For Professional Use Only
£52.85 (incl. VAT)
£44.04 (ex. VAT)
For use with selected products in the Selemix range including Selemix 7-410 2K Epoxy Topcoat. Please see the Product Data Sheet for the Base Product for mixing ratios/application instructions before use For Professional Use Only
£49.72 (incl. VAT)
£41.43 (ex. VAT)
