Sherwin-Williams Leighs C750V2
  • Sherwin-Williams Leighs C750V2

Sherwin-Williams Acrolon C750V2

C750V2

Sherwin-Williams Acrolon C750V2 (formerly known as Leighs C750V2) is an isocyanate free, two-pack finish coat for exterior exposed surfaces where retention of gloss is required, and the use of isocyanate products is precluded or undesirable. Sherwin-Williams Acrolon C750V2 is normally used in conjunction with epoxy primers and undercoats and is Highways Agency and Network Rail approved.

Colour
  • Current colour: RAL1000 - Green Beige
Choose a colour
Close colour picker
  • RAL1000 - Green Beige
  • RAL1001 - Beige
  • RAL1002 - Sand Yellow
  • RAL1003 - Signal Yellow
  • RAL1004 - Golden Yellow
  • RAL1005 - Honey Yellow
  • RAL1006 - Maize Yellow
  • RAL1007 - Daffodil Yellow
  • RAL1011 - Brown Beige
  • RAL1012 - Lemon Yellow
  • RAL1013 - Oyster White
  • RAL1014 - Ivory
  • RAL1015 - Light Ivory
  • RAL1016 - Sulfur Yellow
  • RAL1017 - Saffron Yellow
  • RAL1018 - Zinc Yellow
  • RAL1019 - Grey Beige
  • RAL1020 - Olive Yellow
  • RAL1021 - Rape Yellow
  • RAL1023 - Traffic Yellow
  • RAL1024 - Ochre Yellow
  • RAL1027 - Curry
  • RAL1028 - Melon Yellow
  • RAL1032 - Broom Yellow
  • RAL1033 - Dahlia Yellow
  • RAL1034 - Pastel Yellow
  • RAL2000 - Yellow Orange
  • RAL2001 - Red Orange
  • RAL2002 - Vermilion
  • RAL2003 - Pastel Orange
  • RAL2004 - Pure Orange
  • RAL2008 - Bright Red Orange
  • RAL2009 - Traffic Orange
  • RAL2010 - Signal Orange
  • RAL2011 - Deep Orange
  • RAL2012 - Salmon Orange
  • RAL3000 - Flame Red
  • RAL3001 - Signal Red
  • RAL3002 - Carmine Red
  • RAL3003 - Ruby Red
  • RAL3004 - Purple Red
  • RAL3005 - Wine Red
  • RAL3007 - Black Red
  • RAL3009 - Oxide Red
  • RAL3011 - Brown Red
  • RAL3012 - Beige Red
  • RAL3013 - Tomato Red
  • RAL3014 - Antique Red
  • RAL3015 - Light Pink
  • RAL3016 - Coral Red
  • RAL3017 - Rose
  • RAL3018 - Strawberry Red
  • RAL3020 - Traffic Red
  • RAL3022 - Salmon Pink
  • RAL3027 - Raspberry Red
  • RAL3031 - Orient Red
  • RAL4001 - Red Lilac
  • RAL4002 - Red Violet
  • RAL4003 - Heather Violet
  • RAL4004 - Claret Violet
  • RAL4005 - Blue Lilac
  • RAL4006 - Traffic Purple
  • RAL4007 - Purple Violet
  • RAL4008 - Signal Violet
  • RAL4009 - Pastel Violet
  • RAL4010 - Telemagenta
  • RAL5000 - Violet Blue
  • RAL5001 - Green Blue
  • RAL5002 - Ultramarine Blue
  • RAL5003 - Sapphire Blue
  • RAL5004 - Black Blue
  • RAL5005 - Signal Blue
  • RAL5007 - Brilliant Blue
  • RAL5008 - Grey Blue
  • RAL5009 - Azure Blue
  • RAL5010 - Gentian Blue
  • RAL5011 - Steel Blue
  • RAL5012 - Light Blue
  • RAL5013 - Colbalt Blue
  • RAL5014 - Pigeon Blue
  • RAL5015 - Sky Blue
  • RAL5017 - Traffic Blue
  • RAL5018 - Turquoise Blue
  • RAL5019 - Capri Blue
  • RAL5020 - Ocean Blue
  • RAL5021 - Water Blue
  • RAL5022 - Night Blue
  • RAL5023 - Distant Blue
  • RAL5024 - Pastel Blue
  • RAL6000 - Patina Green
  • RAL6001 - Emerald Green
  • RAL6002 - Leaf Green
  • RAL6003 - Olive Green
  • RAL6004 - Blue Green
  • RAL6005 - Moss Green
  • RAL6006 - Grey Olive
  • RAL6007 - Bottle Green
  • RAL6008 - Brown Green
  • RAL6009 - Fir Green
  • RAL6010 - Grass Green
  • RAL6011 - Reseda Green
  • RAL6012 - Black Green
  • RAL6013 - Reed Green
  • RAL6014 - Yellow Olive
  • RAL6015 - Black Olive
  • RAL6016 - Turquoise Green
  • RAL6017 - May Green
  • RAL6018 - Yellow Green
  • RAL6019 - Pastel Green
  • RAL6020 - Chrome Green
  • RAL6021 - Pale Green
  • RAL6022 - Olive Drab
  • RAL6024 - Traffic Green
  • RAL6025 - Fern Green
  • RAL6026 - Opal Green
  • RAL6027 - Light Green
  • RAL6028 - Pine Green
  • RAL6029 - Mint Green
  • RAL6032 - Signal Green
  • RAL6033 - Mint Turquoise
  • RAL6034 - Pastel Turquoise
  • RAL7000 - Squirrel Grey
  • RAL7001 - Silver Grey
  • RAL7002 - Olive Grey
  • RAL7003 - Moss Grey
  • RAL7004 - Signal Grey
  • RAL7005 - Mouse Grey
  • RAL7006 - Beige Grey
  • RAL7008 - Khaki Grey
  • RAL7009 - Green Grey
  • RAL7010 - Tarpaulin Grey
  • RAL7011 - Iron Grey
  • RAL7012 - Basalt Grey
  • RAL7013 - Brown Grey
  • RAL7015 - Slate Grey
  • RAL7016 - Anthracite Grey
  • RAL7021 - Black Grey
  • RAL7022 - Umbra Grey
  • RAL7023 - Concrete Grey
  • RAL7024 - Graphite Grey
  • RAL7026 - Granite Grey
  • RAL7030 - Stone Grey
  • RAL7031 - Blue Grey
  • RAL7032 - Pebble Grey
  • RAL7033 - Cement Grey
  • RAL7034 - Yellow Grey
  • RAL7035 - Light Grey
  • RAL7036 - Platinum Grey
  • RAL7037 - Dusty Grey
  • RAL7038 - Agate Grey
  • RAL7039 - Quartz Grey
  • RAL7040 - Window Grey
  • RAL7042 - Traffic Grey A
  • RAL7043 - Traffic Grey B
  • RAL7044 - Silk Grey
  • RAL7045 - Telegrey 1
  • RAL7046 - Telegrey 2
  • RAL7047 - Telegrey 4
  • RAL8000 - Green Brown
  • RAL8001 - Ochre Brown
  • RAL8002 - Signal Brown
  • RAL8003 - Clear Brown
  • RAL8004 - Copper Brown
  • RAL8007 - Fawn Brown
  • RAL8008 - Olive Brown
  • RAL8011 - Nut Brown
  • RAL8012 - Red Brown
  • RAL8014 - Sepia Brown
  • RAL8015 - Chestnut Brown
  • RAL8016 - Mahogany Brown
  • RAL8017 - Chocolate Brown
  • RAL8019 - Grey Brown
  • RAL8022 - Black Brown
  • RAL8023 - Orange Brown
  • RAL8024 - Beige Brown
  • RAL8025 - Pale Brown
  • RAL8028 - Terra Brown
  • RAL9001 - Cream
  • RAL9005 - Black
  • RAL9010 - White
  • RAL9002 - Grey White
  • RAL9003 - Signal White
  • RAL9004 - Signal Black
  • RAL9011 - Graphite Black
  • RAL9016 - Traffic White
  • RAL9017 - Traffic Black
  • RAL9018 - Papyrus White
Size
Finish
£82.66
VAT excluded

£99.19 Tax incl.
Quantity

Description

Sherwin-Williams Acrolon C750V2 (formerly known as Leighs C750V2) is an isocyanate free, two-pack finish coat for exterior exposed surfaces where retention of gloss is required, and the use of isocyanate products is precluded or undesirable. Sherwin-Williams Acrolon C750V2 is normally used in conjunction with epoxy primers and undercoats and is Highways Agency and Network Rail approved.

Endorsements

  • Network Rail approved as an Isocyanate free finish.
  • Highways Agency No: 167

Resistance to

  • Moisture - Good
  • Aliphatic solvents - Moderate
  • Acid spillage - Moderate
  • Abrasion - Moderate
  • Alkali spillage - Moderate
  • Weather - Excellent

Recommended Primers

Compatible with a wide range of Macropoxy, Dura-plate, Zinc Clad Epoxy Primers and Buildcoats. Acrolon C750V2 must be applied over epoxy materials within 4 days at 23°C to ensure satisfactory intercoat adhesion.

Application Conditions & Overcoating

This material should preferably be applied at temperatures in excess of 10ºC. In conditions of high relative humidity, ie 80-85% good ventilation conditions are essential. Substrate temperature shall be at least 3ºC above the dew point and always above 0°C. At application temperatures below 10°C, drying and curing times will be signifi cantly extended, and spraying characteristics may be impaired. Application at ambient air temperatures below 5°C is not recommended.
Steelwork coated with Acrolon C750V2 Special Finish should be protected from weather for 48-72 hours after application, depending on conditions. Consult our Technical Team if in doubt.

Additional Notes

Drying times, curing times and pot life should be considered as a guide only. The curing reaction of the material commences immediately the two components are mixed, and since the reaction is dependent on temperature, the curing time and pot life will be approximately halved by a 10°C increase in temperature and doubled by a 10°C decrease in temperature.

Tropical Use

Acrolon C750V2 at the time of mixing should not exceed a temperature of 35°C.  Use of this product outside its pot life may result in inferior adhesion properties even if the material appears fit for application. Thinning the mixed product will not alleviate this problem.

It is not advisable to apply this coating when the air and substrate temperatures exceed 45°C. These conditions can introduce paint film formation defects, such as dry spray, bubbling and pinholing etc. Numerical values quoted for physical data may vary slightly from batch to batch.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
C750V2

Data sheet

Typical Coverage (per coat)
10.6m² per litre
Touch Dry
1 Hour
Application
Brush, Spray
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


questions Matt Burrows on 12/02/2019
Question: 

metal-paints/metal-topcoats/1932-sherwin-williams-acrolon-c750v2 Can this be made in BS 381C 175 Light French blue?

Answer: 

Yes, you can order this with us via telephone on 0113 2455450.


Question about the product

* Required fields
(read)
Send
16 other products in the same category:

Bradite HD Floor + Wall

Bradite HD Floor + Wall is a heavy-duty coating for walls and floors that is well-suited to factory and industrial environments that need ultra protection and an easy-to-clean surface. Also suitable for hygene-sensitive areas such as hospitals and more. Advantages Water-based epoxy coating Conforms to ISO 9001:2008 quality & ISO 14001:2004 Resists...

Price £83.52
In stock

Nullifire PM018 Primer or Top Seal Epoxy Coating

Nullifire PM018 Primer or Top Seal Epoxy Coating is a two-components modified epoxy coating. It is a heavy duty, high build coating for protection of steel in corrosive environments and is excellent for use at low temperatures. 

Price £311.85
In stock

Bradite HB MIO Coat/Finish

A high build high performance single pack modified alkyd micaceous iron oxide intermediate coat. Gives excellent decorative anti-corrosive properties when used as a coating or finish in a conventional paint system. Conforms to MOD TS10201 specification & BS5493 parts FU2C/FF3D. Advantages Good toughness and abrasion resistance Good UV resistance...

Price £46.79
In stock

International Intergard 740

International Intergard 740 is a two component epoxy finish coat suitable for brush, roller and spray application, suitable for use in a wide range of environments including offshore structures, petrochemical facilities, bridges, pulp and paper mills, and the power industry.

Price £78.90
In stock

Solignum Ionolac

A lead-free gloss paint giving excellent durability and protection on metal, wood and other surfaces, equally suitable for internal use. 

Price £20.25
In stock

Cromadex 842 Two Pack Non-Isocyanate Acrylic Medium Texture Topcoat

Cromadex 842 Two Pack Non-Isocyanate Acrylic Medium Texture Topcoat is a two pack non-isocyanate acrylic medium texture topcoat with excellent exterior durability and chemical resistance. The product uses unique resin and pigment technology enable a wide variety of applications and a durable finish, whilst the medium texture appearance offers an aesthetic...

Price £180.13
In stock

International Interthane 870

International Interthane 870 is high build which means it can reduce the number of coats you require and keep costs to a minimum. Semi-gloss and available in a range of colours, International Interthane 870 delivers excellent cosmetics and extended recoatability in both new construction and as an industrial maintenance.

Price £101.78
In stock

Zinga Zingalufer

Zingalufer, previously known as Alufer N, an intermediate layer or topcoat for existing layers of Zinga in immersed or chemical environments, such as ship hulls and sewage works, providing a protective seal against salt and chemical exposure. Apply by brush, roller, conventional sprayers or aireless spray One pack system Dry in as little...

Price £24.58
In stock

Coo-Var Radiator Enamel

Coo-Var Radiator Enamel is a high performance water based radiator enamel designed for application to domestic hot water radiators. This product is designed to stay white.

Price £16.71
In stock

Carboline Carboxane 2000 Topcoat

Carboline Carboxane 2000 Topcoat is a two pack modified silane multi-polymer, and is a high performance, multi-purpose finishing product, allowing reduced coating specification in corrosion protection. It also adds a new dimension to finishing over Nullifire fire protection.

Price £236.41
In stock

Zinga Aluspray

Aluspray, a finishing coat that improves the aesthetic of Zinga in a handy and economical 500ml aerosol spray can. Ideal for spot treatment on small areas and touching up HDG, metallisation or previously treated Zinga surfaces. Efficient and solid Aluminium colour (~RAL 9006: comparable to hot-dip) Good resistance to mechanic shocks,...

Price £13.70
In stock

Cromadex 232 One Pack Air Drying Alkyd Medium Texture Topcoat

Cromadex 232 One Pack Air Drying Alkyd Medium Texture Topcoat is a one pack air drying topcoat that comes in a medium texture finish that adds value to your product. The product has a long wet edge that enables a seamless finish on large articles without dry spray. Available in the full Cromadex range of colours, including BS, RAL and special matches all...

Price £70.39
In stock

Jotun Hardtop HB

Jotun Hardtop HB is a two component chemically curing aliphatic acrylic polyurethane coating that has a matt finish with very good gloss retention. It is a high build product that can be used as a topcoat in atmospheric environments. Jotun Hardtop HB is recommended for topside, deck and superstructure areas in the marine industry.

Price £51.51
In stock