HMG Stoving Enamel is a high performance, rapid curing, high build, general purpose stoving enamel. Stoving paints are for force-drying; for painting stoves, see our heat-resistant paints
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
HMG Stoving Enamel is a high performance, rapid curing, high build, general purpose stoving enamel.
| Technical Data | |
|---|---|
| Volume Solids: | 50.6% |
| VOC Content: | 0.5 Kg/l |
| SG: | - |
| Viscosity: | 150 mPas |
| Density: | 0.982 g/cm³ |
| Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed. |
| Shelf Life: | 12 months from delivery date in original sealed containers. |
| Flash Point: | 4°C |
| Product Data | |||
|---|---|---|---|
| Dry Film Thickness | Wet Film Thickness | ||
| Compliant Spray Gun: | 25 μm | 50 μm | |
| Pressure Pot: | 25 μm | 50 μm | |
Coverage: 20 square metres per litre @ 25 microns dft
| Drying Times At 120°C | |
|---|---|
| Fully Cured: | 30 minutes |
| Technical Data | |||||
|---|---|---|---|---|---|
| Gravity Gun | HVLP | ||||
| Mixing Ratio: | Base: 1 | Base: 1 | |||
| Thinner: >20% | Thinner: >20% | ||||
| Thinner Options: | Thinner 2691 | Thinner 2691 | |||
| - | - | ||||
| Viscosity: | 25 - 35 seconds B4 cup | 25 - 35 seconds B4 cup | |||
| Spray Gun Setup: | 1.6 - 1.8 | 1.2 - 1.4 | |||
| Number Of Coats (Guide Only): | 1 - 2 full coats | 1 - 2 full coats | |||
| Flash Off: | 15 minutes | 15 minutes | |||
For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]
HMG Stoving Enamel:
| Information on basic physical and chemical properties | |
|---|---|
| Form: | Liquid |
| Colour: | According to product specification |
| Odour: | Characteristic |
| Odour Threshold: | Not determined |
| pH-value: | Not determined |
| Change in Condition | |
| Melting point/freezing point: | Undetermined |
| Initial boiling point and boiling range: | 108°C |
| Flash Point: | 4°C |
| Flammability (solid, gas): | Not applicable |
| Ignition temperature: | 500°C |
| Decomposition temperature: | Not determined. |
| Auto-ignition temperature: | Product is not selfigniting |
| Explosive properties: | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." |
| Explosion limits: Lower: | 1.1 Vol % |
| Explosion limits: Upper: | 7 Vol % |
| Vapour pressure at 20°C: | 6.7 hPa |
| Density at 20°C: | 0.982 g/cm³ |
| Relative density: | Not determined |
| Vapour density: | Not determined |
| Evaporation rate: | Not determined |
| Solubility in / Miscibility with water: | NOT MISCIBLE |
| Partition coefficient: n-octanol/water: | Not determined |
| Viscosity: Dynamic at 20°C: | 150 mPas |
| Viscosity: Kinematic: | Not determined |
| Solvent content: Organic solvents: | 50.0% |
| Solids content: | 50.6% |
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
 jenkyn knill on 2023-03-09 13:10:32 | Question:
Can this product be applied by brush or is it spray application only? |
Answer from Rawlins’ Technical Team:
This product is suitable for spray application only. | |
| Don Kiddick on 2022-10-31 19:22:47 | Question:
What temperature level can this paint can resist? |
Answer from Rawlins’ Technical Team:
This product can resist upto 160°C. | |
| Jayne Phelps on 2022-09-08 07:40:17 | Question:
Have you a paint that is suitable for repainting /spraying Aga type cooker ? On site Kings regards Jayne Phelps |
Answer from Rawlins’ Technical Team:
No, unfortunately we do not have a product we can recommend for this application. | |
| Nikki Parsler on 2022-09-06 10:18:46 | Question:
Can I use this to paint front of wood fired rayburn? |
Answer from Rawlins’ Technical Team:
Unfortunately no, we do not have a product to recommend for this application. | |
HMG Stoving Enamel is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
HMG Thinner 2691 is a thinner for use in various applications. For use with compatible HMG systems. More Information Delivery Info
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...
