Kolorbond K2, a two pack PU coating which can be applied directly onto a variety of substrates including PVCu (uPVC), GRP, mill, polyester powder coated & anodised aluminium, stainless steel, hard plastics, cast iron and steel, light alloys, galvanised and phosphated steel, composite doors and even glass.
Please note: hardener in 6L and 30L packs supplied in the correct measured quantities to be mixed together in full to achieve the correct mixing ratio when combined (5 parts base to 1 part hardener). 1.25L pack size (1L Base + 0.25L Hardener) requires just 200ml of hardener into 1L of base, not the full tin.
Kolorbond K2 is based on two pack polyurethane/acrylic technology, making the finished coating highly resistant to abrasion, and other accidental damage. It is very durable, once dry, and easy to apply using any standard spray equipment, either on-site or in a manufacturing environment. For the brush grade version please see Kolorbond DecoPro.
A unique paint that acts as a durable, lightfast coating across a vast range of previously "un-paintable" substrates. Tested and demonstrated effectiveness in coating PVCu (uPVC), GRP, mill, polyester powder coated & anodised aluminium, stainless steel, hard plastics, cast iron and steel, light alloys, galvanised and phosphated steel, composite doors and even glass.
No primer required
In most applications, Kolorbond K2 does not require a primer and is able to be applied in a high film thickness. Most applications are possible in one stage saving substantial time compared to other coatings.
Mask the substrate, covering all surfaces which do not require painting.
Clean the substrate using Vinylkleen. This will remove all water soluble contaminants together with most oils.
Thoroughly clean the surface again using Windowprep on a clean white cloth which should be regularly turned.
Lightly abrade the surfaces to be painted with red Scotchbrite and remove debris. Uncoated metals must be abraded with a grit paper to remove any oxidation.
Check that the paint colour and gloss level are correct. Thoroughly stir the Kolorbond K2 paint making sure that any colourants on the base of the can are mixed in.
Stir in the required amount of K2 Hardener, 5:1 by volume (6L and 30L packs only; for 1.25L pack size, hardener is supplied in 250ml size but only 200ml is required). The paint will now have a maximum pot life of 2 hours. Only mix the amount of paint you can use in that time.
If spraying glass, add 10% G-pro Glass Additive (available under "Add ons" further above) and mix in thoroughly
Use a tack rag, if necessary, to remove any dust or swarf remaining on the surface of the substrate.
The sprayer must use a mask suitable for 2 pack paint. Skin must be protected by the use of gloves etc.
Spray the substrate with a dust coat followed by a medium coat.
Allow the first coat to flash off then apply a second coat. A third coat may be added if a dry finish of up to 90µ thickness is required. Any inclusions should be removed gently, with red Scotchbrite, between coats.
The paint will cure and harden overnight. The paint can still emit solvents after curing so leave as long as possible before applying protective tape.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Hello, Is this paint solvent soluble? I previously used this product and the colour was wrong not on your behalf the customers instead. I have since had to locally source the correct white which has been made up in a one pack coat (techno grip) Kind regards Mike
Answer from Rawlins’ Technical Team:
If the Kolorbond K2 Set has been allowed to fully cure then there should not be an issue with solvents affecting this. We would recommend contacting "Techno grip" for their advice on overcoating third party two pack products, an area to test for compatability may be required.
Kolorbond K2 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
Kolorbond K2 Thinner, for use with Kolorbond K2 and the brush grade version Kolorbond DecoPro a two pack PU coating which can be applied directly onto a variety of substrates including uPVC, metals, GRP and hard plastics.
More Information Delivery Info
Kolorbond K2 Accelerator is for use with Kolorbond K2 and the brush grade version Kolorbond DecoPro, two pack PU coatings which can be applied directly onto a variety of substrates including uPVC, metals, GRP and hard plastics.
K2 Accelerator is used to accelerate the curing process of Kolourbond K2 and Kolorbond DecoPro when added at 2%....
Kolorbond WindowPrep is an alcohol based cleaner for use on PVCu prior to painting. It is very important that PVCu (uPVC) is cleaned with WindowPrep prior to painting; WindowPrep not only removes contaminants but also removes plasticizers from the surface of the PVCU and, additionally, opens the pores of the PVCu which greatly assists adhesion...
Kolorbond C425 Retarder can be added to single pack, solvent based Kolorbond paint to slow down drying times.
Very useful when spraying large panels or spraying large areas on site, the increased drying time allows the sprayer to keep a wet edge.
It is also known as Kolorbond K2 Retarder and it may be added to Kolorbond K2 when spraying...
Kolorbond DecoPro is a brushable version of Kolorbond K2. It is a two pack PU coating which can be applied directly onto a variety of substrates including PVCu (uPVC), GRP, mill, polyester powder coated & anodised aluminium, stainless steel, hard plastics, cast iron and steel, light alloys, galvanised and phosphated steel, composite doors...