Zeroflame Samples allow you to check the suitability, colour and the texture of selected Zeroflame products.
Please see below for details of all currently available samples, including links to the main products for detailed Product and Safety information.
Quick Links - Click To Jump To Section:
Zeroflame Fire Retardant Treatment Sample
Zeroflame Fire Retardant Treatment 250ml Sample is a water based, clear solution that soaks into wood to leave the appearance of the timber virtually unchanged. Applied by brush, roller, spray, or immersion it achieves Euroclass B s2 d0 (replaces UK Classes ‘0’ and ‘1’ BS 476 Part 6/7*) on solid timbers. Zeroflame Fire Retardant Treatment can be used inside or out and the fire retardant properties will remain active for the lifetime of the substrate.
Zeroflame Fire Retardant Treatment soaks into the woods surface, without leaving a clear glaze on top like a varnish. It then dries with virtually no evidence of the wood ever been treated, allowing you to keep the woods natural beauty. Zeroflame Treatment does not require over coating, however it can be over coated with waterborne, non-flammable stains, varnishes and paints for decoration and/or protection if desired (care should be taken that the fire retardant properties are not compromised).
Please Note: Timber must be a minimum of 12mm thick for the treatment to be effective.
Un-Matched Performance
To say that Zeroflame Fire Retardant Treatment is revolutionary is an understatement, this remarkable product will protect timber substrates in commercial and domestic environments, can be used internally and externally, is not affected by moisture or humidity when dry, is non-hazardous, non-corrosive and virtually odour free, the list goes on! Never before has there been such a simple product to use for the protection of timber against fire.
Zeroflame's Fire Resistant Products
Find out more about other fire retardant paints and intumescent coatings from Zeroflame here, all available at Rawlins Paints.
- 250ml Sample size available
Please note the below regarding 250ml samples:
- No fire certificates can be requested or provided following purchase of a 250ml sample regardless of project size
- 250ml Sample covers up to 1m²
- We would always recommend a sample be taken to check appearance, absorption and any potential topcoat compatibility prior to purchasing any larger amount
Zeroflame Fire Retardant Treatment Advantages
- Moisture resistant and unaffected by humidity
- Classifies solid wood as having little or no contribution to fire
- Tested to EN 927-6 & EN16755 accelerated weathering: rated as EXT1.
- Simple specification
- Suitable for non-specialist application
- Suitable for off-site application
- Non-corrosive
- Non-hazardous
- Virtually odour free
- Unaffected by wear
- Maintenance free
- Does not require over coating except for decoration
For the full product please see Zeroflame Flame Retardant Treatment.
Certification
- No fire certificates can be requested or provided following purchase of a sample regardless of project size
Limitations
- Discolouration may occur on some types of timber or on heavily knotted wood. If this is a concern it is recommended that a sample area is completed before application to the whole project. Alternatively, application of a compatible varnish or stain AFTER application of Zeroflame Fire Retardant Treatment may help overcome this phenomenon if it is unacceptable
- Zeroflame Fire Retardant Treatment is not suitable for veneer, plywood laminates, wood-derived particle board or similar as it cannot penetrate. Zeroflame Fire Retardant Paint or Thermoguard Fire Varnish BS Class 1/0 & EN Class B System is recommended instead
* This product has not been tested to BS 476 Parts 6 & 7, Class 1/0 so if this is the level of protection you require you should check with your authority prior to use that they will accept BS EN 13501-1:2018 B s2 d0 as a suitable alternative before proceeding.
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions and should be applied only by an individual with the necessary expertise and experience. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.