HMG High Build Vinyl Primer Finish Aerosol is a 1K high build anti corrosive vinyl primer finish. This product has also been designed to be “Ready for Use”, for the non-aerosol version of this product please see HMG High Build Vinyl Primer Finish.
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
HMG High Build Vinyl Primer Finish Aerosol is a 1K High Build Anti Corrosive Vinyl Primer Finish designed to give excellent adhesion and corrosion protection to mild steel, aluminium, stainless steel and galvanised substrates. This product has also been designed to be “Ready for Use”, for the non-aerosol version of this product please see HMG High Build Vinyl Primer Finish.
| Technical Data | ||||||
|---|---|---|---|---|---|---|
| High Build Vinyl Primer Finish Aerosol | ||||||
| Volume Solids: | 23.7% | |||||
| VOC Content: | - | |||||
| SG: | - | |||||
| Viscosity: | Not Determined | |||||
| Density: | 0.828 g/cm³ | |||||
| Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed | |||||
| Shelf Life: | 12 months from delivery date in original sealed containers | |||||
| Pot Life: | - | |||||
| Flash Point: | -42°C | |||||
| Product Data | |||
|---|---|---|---|
| Dry Film Thickness | Wet Film Thickness | ||
| Aerosol: | 30 - 60 μm | 75 - 150 μm | |
Coverage: 12.5 square metres per litre @ 50 microns dft
| Drying Times At 20°C | |||
|---|---|---|---|
| Touch Dry: | 60 minutes | ||
| Fully Cured: | 12 hours | ||
| Technical Data | |||||
|---|---|---|---|---|---|
| Aerosol | |||||
| Mixing Ratio: | Ready for use | ||||
| - | |||||
| Thinner Options: | - | ||||
| Viscosity: | - | ||||
| Spray Gun Setup: | - | ||||
| Number Of Coats (Guide Only): | 1 - 2 full coats | ||||
| Flash Off: | - | ||||
For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]
| Information On Basic Physical And Chemical Properties | ||||||
|---|---|---|---|---|---|---|
| High Build Vinyl Primer Finish Aerosol | ||||||
| Form: | Aerosol | |||||
| Colour: | According to product specification | |||||
| Odour: | Characteristic | |||||
| Odour Threshold: | Not determined | |||||
| pH-value 20°C: | Not determined | |||||
| Melting point/freezing point: | Undetermined | |||||
| Initial boiling point and boiling range: | -24.9°C | |||||
| Flash Point: | -42°C | |||||
| Flammability (solid, gas): | Not applicable | |||||
| Ignition temperature: | 235°C | |||||
| Decomposition temperature: | Not determined | |||||
| Auto-ignition temperature: | Product is not selfigniting | |||||
| Explosive properties: | Not Determined | |||||
| Explosion limits: Lower: | 3.0 Vol% | |||||
| Explosion limits: Upper: | 18.6 Vol% | |||||
| Vapour pressure at 20°C: | 5200 hPa | |||||
| Density at 20°C: | 0.828 g/cm³ | |||||
| Relative density: | Not determined | |||||
| Vapour density: | Not determined | |||||
| Evaporation rate: | Not applicable | |||||
| Solubility in / Miscibility with water: | NOT MISCIBLE | |||||
| Partition coefficient: n-octanol/water: | Not determined | |||||
| Viscosity: Dynamic at 20°C: | Not determined | |||||
| Viscosity: Kinematic: | Not determined | |||||
| Solvent content: Organic solvents: | 76.2% | |||||
| Solids content: | 23.7% | |||||
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
HMG High Build Vinyl Primer Finish Aerosol is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
HMG High Build Vinyl Primer Finish is a high build anti corrosive vinyl primer finish.Excellent adhesion Corrosion protection to mild steel, aluminium, stainless steel and galvanised substrates Available in 5,000+ colours from RAL, NCS, and British Standard Also available as an aerosol, please see HMG High Build Vinyl Primer Finish...
£83.10 (incl. VAT)
£69.25 (ex. VAT)
HMG Prep Clean 2802 is a fast evaporating, strong Preparatory Cleaning solvent for the heavy duty degreasing of substrates.Used in many applications For use on bare surfaces onlyMore Information Delivery Info
£44.83 (incl. VAT)
£37.36 (ex. VAT)
HMG Thinner 2621 is a thinner for use in various applications.For use with compatible HMG systems.More Information Delivery Info
£13.37 (incl. VAT)
£11.14 (ex. VAT)
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...
£25.84 (incl. VAT)
£21.53 (ex. VAT)
