- There are no more items in your cart
- Shipping Calculated at checkout
- Sub-Total(ex. VAT)(inc. VAT)£0.00£0.00
We no longer stock this product, but can recommend Rust-Oleum 9200 Rust-O-Thane (water based and satin finish) or Teamac High Performance Polyurethane Topcoat (solvent based and gloss finish) as a great alternative.
We no longer stock this product, but can recommend Rust-Oleum 9200 Rust-O-Thane (water based and satin finish) or Teamac High Performance Polyurethane Topcoat (solvent based and gloss finish) as a great alternative.
Bradite Poly Lacquer is a two-pack polyurethane, clear coating and finish lacquer, for mineral substrates, and wood. Also suitable for bar tops and dance floors. Producing a tough, hard-wearing coating that is recoatable even after long periods of exposure. Can be used as an anti-graffiti coating on suitable substrates.
Important note: this product is intended for professional use only.
Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems. 2004/42/EC EU limit value for this product (cat.A/j sb): 500g/l (2010). This product contains max. 405 g/l VOC.
Features & Benefits
- Available in more than 350 colours in RAL & BS
- Tough hard-wearing film coating.
- Good chemical resistance.
- Excellent resistance to weathering.
- Can be used as an anti-graffiti coating on suitable surfaces.
- Cures at low temperatures.
Preparation
For internal & external steel & non-ferrous substrates which are dry, free of contamination and have been properly prepared and primed. May also be applied to wood, fibreglass, concrete and other mineral surfaces that are properly prepared and free of contamination, dust and efflorescence. Compatibility with existing coatings should be confirmed by preparing and painting a test patch. Not suitable for applying over asphalt, bitumen, epoxy tar, alkyd, chlorinated rubber or vinyl based paints.
High pressure steam cleaning to remove all loose, flaking paint and contamination back to a sound surface. Bradite TD39 industrial strength detergent, washing and rinsing should be used with scrubbing to remove grease or oil. Sound existing coating should be additionally abraded to provide a key.
1st coat: Bradite Poly Lacquer PL78, thinned 20% with TP33, if required.
2nd coat: Bradite Poly Lacquer PL78.
For maintenance painting the 1st coat will be a touch up to bare areas only.
Always refer to the Health and Safety sheet for the product before use, and observe the warning phrases on the label.
Application
Application and use should always conform to the codes of practice described in BS 6150 and BS 5493.
Brush and Roller: Supplied ready for use. Thin, if required, with 0-5% Bradite Thinner TP33.
Conventional Air Spraying: Thin with 5-15% Bradite Thinner TP33 as required, tip size – 1.5mm, tip pressure 60psi (0.4MPa) approximately.
Airless Spraying: Thin with 0-10% Bradite Thinner TP36 as required, tip size - 13 thou (0.33mm) approximately, tip pressure - 2100 psi (15MPa) approximately.
Clean all equipment immediately after use with Bradite Thinner TP33 for best results.
Data sheet
- For Use On
- Steel, Non-Ferrous Metals, Wood, Concrete
- Application Method
- Brush, Roller, Spray
- Sheen
- Gloss, Semi-Gloss
- Colour
- Fully Tintable
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 2.5L
- Application
- Brush, Roller, Spray
- Coverage
- 15m2 per Litre
- Touch Dry
- 1 Hour
- UN Number
- UN1263
- Brand
- Bradite
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Bradite Poly Lacquer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT