• RSL Resuthane SL23

RSL Resuthane SL23

Resuthane™ SL23 is a self-smoothing resin floor screed that when installed at 2mm-3mm to a seamless surface, provides excellent anti-slip properties. It is designed to resist very aggressive industrial environments.

ADVANTAGES

  • High chemical resistance
  • Resistance to hot water
  • Self sealing
  • Matt finish
  • Extremely hard wearing
Colour
  • Current colour: Black
Choose a colour
Close colour picker
  • Black
  • Salsa Red
  • Stirling Grey
  • Flint Grey
  • Buff - RSL
  • Kingfisher Blue - RSL
  • Forest Green - RSL
  • Marigold
Size
Finish
£49.52
VAT excluded

£59.42 Tax incl.
Quantity

Description

Resuthane™ SL23 is ideal for large and small areas alike where a hard-wearing, sustainable and smooth floor is essential. A major asset is the simplicity with which it can be cleaned and maintained, as well as its chemical resistant, non-taint and non-dusting qualities.

Resuthane SL23 is ideal for a variety of industrial settings where conditions can change from dry to wet and where anti-slip is essential for the safety of employees. 

RECOMMENDED USES

  • Food manufacture & processing
  • Brewing & beverage
  • Dairies
  • Commercial Kitchens
  • Pharmaceutical & chemical plant processing
  • Abattoirs
  • Medical & Healthcare

Preparation

New Concrete Floors: New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm sq. is required.

Existing Concrete Floors: Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue of detergent is washed and removed by rinsing with clean water.

Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. if the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with existing floor coating.

To ensure the maximum bond is achieved, grooves must be cut into the perimeter of the subfloor, typically 5mm deep by 10mm wide. These should be inset approximately 150mm from, and running parallel with the walls and adjacent to any doorways, plinths etc. including any finished edge, i.e. both sides of a day work joint. The groove must have a neat square edge and the Resuthane SL23 laid to the full depth forming a perimeter anchorage.

Priming

Open and porous substrates will require priming with Resuprime ST on dry substrates only with less than 75% ERH reading. Where the relative humidity of a substrate exceeds 75% ERH, Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.

The number of coats to be applied is chosen in accordance with the following table:

ERH% Required Coating Thickness
75-85 1coat of Resuprime MVT at 200 microns per coat
85-92 2coats of Resuprime MVT at 200 microns per coat
92-97 3coats of Resuprime MVT at 200 microns per coat

For further information please refer to individual product data sheets.

Application

Resuthane™ SL23 may be applied to substrates with a surface temperature in the range of 5-20°C and a relative humidity <90% RH, with a minimum air temperature of 8°C and no condensation. Do not pre-warm this product as working times will be substantially reduced if materials are warm.

When the primed surface is tack free Resuthane™ SL23 should be applied at the required rate as soon after mixing as possible. (Delay can result in variation in surface finish, colour and add to application problems).

NB: Cure times are extended at low temperatures.

Mixing: Mix the coloured base component to an even consistency, ensuring the re-dispersion of any settled pigment, thoroughly scrape the contents of the base and hardener components into the same container and mix thoroughly for one minute. Pour the combined base and hardener into a rotary drum mixer and add the aggregate component steadily, until a homogeneous mix of the three components is achieved.

When thoroughly mixed the compound should be poured evenly over the appropriate area to be covered (monitoring rate of coverage to ensure correct depth of screed). Low floor temperatures and reduced thickness may reduce the flow properties of these products. Work out the mix rapidly and evenly over the area with a notched trowel, pin rake or similar to the appropriate thickness. Roll immediately with a spiked roller to achieve an even smooth surface and remove entrapped air.

NB: Spiked rolling should be undertaken immediately after trowelling. Do not re-roll later.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details

Data sheet

Application
Spiked Roller
Coverage
16 kg will cover 2.8 sq m @ 3mm
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

RSL Resuprime ST

Resuprime ST (formerly known as Resuprime) is a two-pack, solvent-free epoxy resin bonding and priming coat. It bonds resin-based screeds and toppings to cementitious and other surfaces.  Features and Benefits: Versatile for many types of application Excellent adhesive properties Easy to apply Can be used as a tack coat for screeds No...

Price £68.19
In stock

RSL Resuprime MVT

RSL Resuprime MVT (formerly known as R.S. Dampshield FH) is a faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood.  Features and Benefits:...

Price £19.80
In stock
16 other products in the same category:

Sikafloor 330

Sikafloor 330 is a two part, solvent free, very low VOC emission certified, elastic, self-smoothing PUR resin that is an elastic smooth wearing course as part of the Sika ComfortFloor and Sika ComfortFloor Pro systems.

Price £213.24
In stock

RSL R.S. Dampshield

R.S. Dampshield is a two-component epoxy resin primer. which enables floor coverings such as carpets, tiles, wood and vinyl to be applied sooner. It allows concrete to dry faster, combating the residual moisture in your concrete floor. ADVANTAGES Easy application Solvent-free Low odour Excellent adhesion Image already added

Price £66.94
In stock

Rust-Oleum 9100 High Solids Epoxy

A higher solids, better coverage and lower VOC content product than the standard 9100 Epoxy. Two-pack, glossy epoxy coating for metal, walls and floors. The most efficient epoxy system providing a very hard coating with high layer thickness for lasting results even with a single coat application.

Price £108.16
In stock

Sikafloor 300 N

Sikafloor 300 N is a two part, solvent free, low VOC emission certified, elastic, self-smoothing ComfortFloor, PUR resin. Provides an elastic, smooth wearing course for concrete and other cement based substrates for Sika ComfortFloor Decorative and Sika ComfortFloor Decorative Pro.

Price £388.93
In stock

Sikafloor 16 Pronto

Sikafloor 16 Pronto is a two-part, fast curing seal coat based on reactive acrylic resins for the Sikafloor Pronto Modular System. Sikafloor Pronto Pigment should be used to colour Sikafloor 16 Pronto where required.

Price £314.84
In stock

Remmers Epoxy BS 3000 SG New

Remmers Epoxy BS 3000 SG New is a high quality, silk gloss, water emulsifiable, pigmented, epoxy resin binder used as a sealant that can be subjected to various loads indoors as well as outdoors. By adding Remmers Selectmix SBL (degree of filling 1:1.5), very economical, water vapour diffusion-open levelling compounds and coatings can be...

Price £83.52
In stock

Hydron Nu-Base PU Floor Finish

Nu-Base PU Floor Finish has the power to withstand tough applications, where temperatures may reach 150°C, or where chemicals may be present. Advantages Excellent for industrial flooring. Two pack solvent-based. FeRFA Class Type 2. Excellent for industrial flooring.

Price £203.75
In stock

Coo-Var Profloor 2 Pack Epoxy Floor Paint

Coo-Var Profloor 2 Pack Epoxy Floor Paint is an exceptionally hard wearing water-based, solvent free two pack epoxy floor paint coating, suitable for heavy duty traffic and wear.  It can be used for projects both inside or outside and is ideal for use in heavy traffic areas with fork trucks and vans.

Price £89.17
In stock

Sikafloor 305 W

Sikafloor 305 W is a two part, waterbased, low VOC PUR coloured matt seal coat that is part of the Sika ComfortFloor and Sika ComfortFloor Pro systems. Easy to clean, good UV resistance and low odour.

Price £409.84
In stock

Sikafloor 32 Pronto

Sikafloor 32 Pronto, 2-part PU modified PMMA elastomeric binder for self-smoothing screed, broadcasted systems and levelling mortars based on reactive acrylic resins for flooring and car park deck application.

Price £384.93
In stock

RSL Resustat TG69

Resustat TG69 is a heavy duty, water-based polyurethane resin screed for highly aggressive environments, with anti-static qualities compliant with BS 2050 for industrial applications.  ADVANTAGES High chemical resistance Thermal shock and abrasion resistance Resistant to liquids up to 100°C Anti-slip Matt finish Decorative Image...

Price £99.95
In stock

Sikafloor 21 PurCem

Sikafloor 21 PurCem is a multi-component, medium to high strength coloured polyurethane modified, cement and aggregate screed with self-smoothing properties. From the Sikafloor product range, this has an aesthetic, easy to clean, smooth textured aggregate surface providing medium slip resistance.

Price £88.59
In stock

PPG Nu-Klad 814B

PPG Nu-Klad 814B is a solvent free epoxy-based coating used for the protection of concrete floors in the food and beverage industry, industrial and commercial warehouses, (nuclear) power plants and other locations, where a heavy duty smooth and easy cleanable floor topping is required. High build floor coating with excellent wear and...

Price £356.88
In stock

RSL Resucrete

Resucrete is a three-pack epoxy resin screed for 6mm-9mm thickness that withstands aggressive cleaning methods. It comes in 2 grades: Resuscreed HCS (Granite)Resucrete TS (White) ADVANTAGES Impervious and anti-slip Abrasion/Impact resistant Low odour Chemical resistant - anti-bacterial/fungus growth Refer to ordering references below...

Price £51.62
In stock

306 Self Levelling Floor Coating

A self-levelling epoxy screed laid at 2-3mm by serated trowel/rake and spiked roller leaves an attractive finish with excellent resistance to many chemicals. 

Price £133.96
In stock

Remmers Epoxy Flex PH

Remmers Epoxy Flex PH (old name: Epoxyflex Coating PH) is a resistant coating with residual flexibility for surfaces with vehicle traffic and mechanical loads used for concrete surfaces, e.g. roadways and industrial floors. Ideal for production &amp; storage surfaces, workshops and fabrication halls. Image already added

Price £163.08
In stock