A quick drying, universal road marking and line paint suitable for application on asphalt, concrete and brick, on roads, runways, car parks and sports facilities. Bradite RL52 Roadline Paint is water based, highly durable and water resistant.
High-performance ambient crosslinking water based acrylic line marking paint
Bradite Roadline Paint RL52 is a high-performance ambient crosslinking water based acrylic line marking paint. A quick drying universal line marking paint for use on roads, runways, car parks and sports facilities.
Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems. 2004/42/EC EU limit value for this product (cat. A/b wb): 100g/l (2010). This product contains max.96g/l.
For internal & external asphalt, steel, concrete and other absorbent mineral substrates which are dry, free of contamination, dust, efflorescence laitance and have been properly prepared
Applicable by brush, roller, conventional air spray, or airless spray
Reflectivity can be achieved by using proprietary glass beads
Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems
Surface Preparation
Suitable Surfaces:
For internal/external asphalt, steel, concrete, and other absorbent mineral substrates which are dry, free of contamination, dust, efflorescence laitance and have been properly prepared and primed
Suitably prepared and well adhered existing coatings including polyurethane, epoxy, and chlorinated rubber
External floor surfaces should be above local water table and/or have intact DPM barrier present
Compatibility with existing coatings should be confirmed by preparing and painting a test patch
Surface Preparation:
Substrates should be dust free and completely dry before coating. When painting concrete it is vital to ensure that the substrate is completely dry and free of laitance. Power floated, shiny or unpainted non porous concrete floors should be thoroughly vacuum blast cleaned to a roughness profile of 30-50 microns, or acid etched using Bradite Acid Etch
High pressure water cleaning should be utilised to remove all loose and flaking paint and contamination back to a sound substrate. Bradite Industrial Degreaser industrial strength detergent should be used if necessary to remove all grease and oil
Intact areas of existing coatings should be roughened by abrasive manual or disc rubbing and feathered back to a sound coating edge. Cracks and pits should be filled using a suitable screed or mortar before painting
Application Notes
Mix thoroughly before use. Application and use should always conform to the codes of practice described in BS 6150 and BS 5493
Brush and Roller - Supplied ready for use. Thin, if required, with up to 5% water
Conventional Air Spraying - Thin with 15% water as required, tip size - 2.0mm, tip pressure 60psi (0.4MPa) approximately
Airless Spraying - Thin with 0 - 10% water as required, tip size - 18 thou (0.46mm) approximately, tip pressure - 2100 psi (15MPa) approximately
Painting System:
For application on concrete, wood or other absorbent substrates, the first coat should be thinned 5-10% water to allow penetration into the substrate
1st coat - Bradite Roadline RL52 (thinned)
2nd coat - Bradite Roadline RL52
3rd coat - Bradite Roadline RL52
For maintenance painting the 1st coat will be a touch up to bare areas only.
While the floor will take light foot traffic after overnight drying, full cure may take 4 days at 20°C and should not be subject to heavy traffic for at least 48 hours
Please note that drying/curing times will vary depending on film thickness, temperature, and relative humidity
Bradite Low Slip Hard Aggregate LS30 should be added to the paint and mixed thoroughly just before use at a rate of 1 x 250ml LS30 tin (400g) per 5 litres of paint
The end user and applicator must ensure that the finished floor is safe against slips in all likely usage conditions
Cleaning:
Clean all equipment immediately after use with water for best results
Product Details
10436-1036667
Data sheet
Manufacturer
Bradite
For Use By
Consumer Use
Interior / Exterior Use
Interior & Exterior
Water / Solvent Based
Water
For Use On
Asphalt, Steel, Concrete, Mineral Substrates, existing coatings including Polyurethane, Epoxy, and Chlorinated Rubber
Application Method
Brush, Roller, Airless Spray Conventional, Air Spray
Sheen
Semi-gloss
Colour
Standard / Ready Mixed, Fully Tintable
Single, Two or Three Pack
Single
Product Certifications
ISO 9001:2008, ISO 14001:2004 environmental management systems
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Bradite Roadline Paint RL52 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage. Two coats are recoommended for this product.
Bradite Acid Etch is a mineral acid solution used as a pre-treatment for bare concrete surfaces, for application to bare concrete floors to remove excess lime and/or to etch a surface profile to smooth concrete.Provides improved adhesion of subsequent floor coatings Manufactured under the auspices of an ISO 9001:2008 quality & ISO...
Bradite Industrial Degreaser is an aqueous alkaline low foaming detergent used for degreasing contaminated surfaces prior to painting.Ideally suited for degreasing oily or soiled surfaces and for removing road dirt Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systemsMore...
Bradite Low Slip Additive (LS30) is a hard Aluminium Oxide aggregate additive providing additional under foot traction to floor coatings, used in conjunction with Bradite floor paints requiring a hard wearing low slip additive and added to the paint and mixed thoroughly just before use.Manufactured under the auspices of an ISO 9001:2008...