Rust-Oleum Dacfill Frigo Gas & Vapour Tight Coating
Rust-Oleum Dacfill Frigo is a gas & vapour tight coating for walls and ceilings, ideal for use in cold stores. Rust-Oleum Dacfill Frigo has high vapour and gas tightness with permanent high elasticity of up to 400%. It offers resistance against sudden variations in temperature and exhibits high mechanical strength.
Features & Benefits
- Gas and vapour tight rubberlike coating
- Ideal for cold stores and storage rooms
- Resistant against sudden variations in temperature
- Does not contain solvents or bituminous products
- Flexible and impact resistant
- Self-extinguishing (DIN 4102)
Clean the substrate.
Rust-Oleum Dacfill Frigo can be applied on:
- 1. Directly on insulation material such as polystyrene foam, polyurethane and other
- 2. With an adhesion layer, on concrete, bricks, wood, zinc, aluminium, etc.
Directions for Use
To ensure homogeneity, coating materials should be thoroughly stirred prior to use.
Application & Thinning
- Brush: Apply undiluted.
- Roller: Apply undiluted.
- Air-atomised spray: Not recommended
- Airless spray: Nozzle: 018 - 026 / Pressure: 220 bars
- Cleanup: Water
Minimum 5°C / maximum 85% R.H.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Typical Coverage (per coat)
- 0.5 - 1.5kg per m²
- Touch Dry
- 1 Hour 30 Mins
- Brush, Roller, Spray
Be the first to ask a question about this product!
Ideal for walls and ceilings where hygiene control is essential in low wear areas. Offers high durability, perfect saponification resistance, particularly high covering capacity and helps to maintain a hygienic environment.
SikaProof A Edge is a preformed L-shaped SikaProof A membrane sheet in 1m width folded in 50/50cm with a self-adhesive strip on both sides for a faster and easier application of perimeter edges, corners and connections. Used for damp-proofing, concrete protection and waterproofing for basements and other below ground concrete structures against ground...
The Sika Standard Drainage Membrane is an 8mm polypropylene studded membrane used for internal fixing to masonry, stone or concrete walls, dry lined walls, and as a floor membrane where limited water passage is anticipated. Provides a fast track waterproofing solution for walls or floors, suitable for use above and below ground, impermeable to water, gas...
The Sika CD Anti-Lime Coating is a blend of high-grade silicates and wetting agents, held in suspension with water as a carrier. Once applied to the concrete surface, this unique product seals the concrete surface. Reduce “Free Lime” leaching from concrete surfaces, an effective Anti-lime coating to new concrete in Cavity Drain systems. Totally seals the...
SikaProof P-12 is a fully and permanently bonded, self-adhesive, post-applied, composite sheet membrane waterproofing system for reinforced concrete structures. It consists of a flexible polyolefin (FPO) based membrane that is pre-coated with an adhesive sealant layer so that the membrane system is self-adhesive. It is cold- and post-applied, without heat...
Sika BituSeal Primer is a bitumen solution primer to be used in conjunction with Sika BituSeal S-115 to increase adhesion and bond to the substrate. High adhesion and bonding ability on various substrates, good binding ability for dust and loose particles, ready to use by brush, roller or spray.
Sherwin-Williams Macropoxy M630V2 (formerly known as Biogard M630V2) is a water-based, two-pack epoxy gloss finish for interior use only, recommended for application to suitably sealed masonry walls, floors and ceilings. It may also be used on new and old concrete as well as previously painted surfaces and suitably primed steel.
The Sika Cavity Drainage System utilises a high density polypropylene internal drainage membrane, the system is installed loose laid in flooring applications and attached to the wall with surface plugs in vertical installations. Here you can find the associated accessories used with the Sika Cavity Drainage System.
A 2 pack, solvent free, hygienic floor coating from Rust-Oleum for areas where controlled hygienic conditions are of essential importance and where high durability and abrasion resistance is needed.
Rust-Oleum Biosan Aqua Plus is a water-based 2-pack anti-bacterial topcoat for walls and ceilings where hygiene control is essential, like hospitals, kitchens, dairies, breweries, schools etc. Whilst offering exceptional abrasion resistance, it is also water dilutable, solvent free - almost odourless - and easy to clean.
A specially formulated hygienic primer for use with Rust-Oleum 8300 Hygienic Topcoat. As a system it protects against mild chemical exposure, occasional product spillage, frequent chemical cleaning, humidity and moisture. Ideal for walls and ceilings.
A water-based single pack hygienic primer which once overcoated with Rust-Oleum 8700 Hygienic Topcoat protects walls and ceilings against normal humidity and contamination indoors.
The Sika Plaster Drainage Membrane is a 5mm high-density polyethylene cavity drainage studded membrane used for internal fixing to masonry, stone or concrete walls. Suitable for over-plastering/rendering with sand/cement or with Sika Whitewall one coat anhydrite plaster. Easy to cut, fix and seal, unique undercut stud design creates mechanical key for...
Sika BituSeal S-115 is a post applied self-adhesive waterproofing sheet membrane. It is based on SBS (styrene-butadiene-styrene) modified bitumen, reinforced with polyester non woven fabric. It has a silicone-treated release liner on the upper and lower surface. Sika BituSeal S-115 is designed for use as an underlayer in fully self-adhesive multi-ply...
Rust-Oleum’s strongest coating ever, based on the latest rapid curing polyaspartic technology for inside or outside use. This makes Rust-Oleum 9700 Coldmax Rapid (Wintergrade) ideal when extra protection against traffic and chemicals is needed. This versatile coating can also be used outdoors and in cold rooms and freezers.