Carboline Carboquick 200

Reference CRO4860

We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.

Carboline Carboquick 200 is a two-pack fast cure high build polyaspartic coating providing excellent corrosion protection and long term weatherability in just one coat on steel, galvanised and phosphatized. It can be applied direct to metal (DTM) to eliminate the need for typical primers and/or intermediate coats.

Significantly speeds up painting process; saves labour and cost without sacrificing performance
Can be applied over Carbozinc, Carbomastic, or Carboguard primers for even better corrosion protection
Indefinite recoatability
Very good flexibility and elongation
Excellent abrasion and impact resistance, weathering, wetting and adhesion
Extremely durable to help provide long service life
High build, 6 to 10 mils DFT per coat
Meets ISO 12944-6 C3 High
Exceeds SSPC Coating Specification No. 39 Level 3A, highest level for aliphatic polyurea and polyurethane
Gloss finish

Product customisation

Don't forget to save your customization to be able to add to cart

Quantity

Product not available

This Product has been Discontinued

Description

Please note that this product has an extended lead time and a minimum order quantity of 300 litres. It will be subject to additional carriage depending on order size and delivery location. Please contact our sales team on 0113 2455450 or [email protected].

Carboquick 200 is a two-pack fast cure high build polyaspartic coating that provides excellent corrosion protection as well as long term weatherability in just one coat on steel, galvanised and phosphatized.

It can be applied direct to metal (DTM) at 6 to 10 mils dry film thickness (DFT) to eliminate the need for typical primers and/or intermediate coats. This significantly speeds up the painting process, saves labour, and saves money without sacrificing performance. If even better corrosion protection is desired it can be applied over our time proven Carbozinc, Carbomastic, or Carboguard primers.

Click To Jump To Section:

Features and Benefits
Product Specification
Drying Times
Surface Preparation
Application Methods
Application Conditions
Health and Safety

Features and Benefits

Fast cure - speeds the painting process
High build, 6 to 10 mils DFT per coat
Excellent corrosion protection
Meets ISO 12944-6 C3 High, one coat applied DTM
Saves significant time, labour, and money
Excellent weathering
Exceeds SSPC Coating Specification No. 39 Level 3A, highest level for aliphatic polyurea
Exceeds SSPC Coating Specification No. 36 Level 3A, highest level for aliphatic polyurethane
Very good flexibility and elongation
Excellent abrasion and impact resistance
Excellent wetting and adhesion
Extremely durable to help provide long service life
Low VOC and low HAPS
Suitable for use in USDA inspected facilities
Indefinite recoats

Product Specification

Technical Data
	Carboline Carboquick 200
Primer:	Self-priming, DTM, for many applications. For more severe service use with one of the following approved Carboline primers: Carbozinc 11 Series Carbozinc 608 HB Carbozinc 621 with recoat window of 2 to 4 hours at 75 °F Carbozinc 8701 with overnight cure Carboguard 60 Series Carboguard 61 Carboguard 635 Series Carboguard 890 Carbogaurd 8922 Contact Rawlins on Tech - 0113 2455450 (option 2) or [email protected] for recommendations
Volume Solids:	70% +/- 2%
HAPs Values:	0.07 lbs/solid gallon This value may vary by colour
Theoretical Coverage Rate:	27.6 m²/l at 25 microns 4.6 m²/l at 150 microns 2.8 m²/l at 250 microns Allow for loss in mixing and application
Dry Film Thickness:	152 - 254 microns per coat Can be applied at 102-127 microns when applied over approved primer(s)
VOC Values:	As Supplied: 246 g/l These values may vary by colour
Dry Temp. Resistance:	Continuous: 121°C Non-Continuous: 149°C Discolouration may occur at temperatures near 93 °C
Flash Point:	Part A: 5.6°C Part B: 5.6°C
Shelf Life:	Part A: Minimum 24 months at 24°C Part B: Minimum 24 months at 24°C
Storage Temperature and Humidity:	4°C-43°C
Storage Temperature and Humidity:	0-90% Relative Humidity

Drying Times

Curing Schedule
Surface Temp	Dry to Touch	Dry to Handle or Recoat	Final Cure General
2°C	3 Hours	17 Hours	7 Days
4°C	2.5 Hours	16 Hours	7 Days
10°C	2 Hours	7 Hours	7 Days
24°C	30 Minutes	1.5 Hours	4 Days
32°C	30 Minutes	1 Hour	2 Days

These times are based on 50% relative humidity (RH) and 152-254 microns dry film thickness (DFT)
At 4-5 mils DFT (102-127 microns), 23°C, and 50% RH the dry to handle Times are approximately 50-60 minutes
RH lower than 50%, higher film thickness, insufficient ventilation and/or cooler temperatures will require longer cure times and could result in solvent entrapment and premature failure
Excessive humidity and/or condensation on the surface during curing can interfere with the cure, can cause micro-foaming, and may result in loss of sheen and/or discolouration
Maximum recoat times are indefinite
As part of good painting practice it is recommended to first test for adhesion by wiping the surface with Thinner 76 or one of the other solvents listed for thinning.
If the film shows a slight "tack" the surface is suitable for recoating without abrading to create profile

Surface Preparation

General

Remove all contaminants per SSPC-SP 1

Steel

Minimum Commercial Blast Clean per NACE No. 3/SSPC-SP 6 with a 50-75 micron anchor profile for maximum protection

Galvanised Steel

Clean per SSPC-SP 16 with 25-75 micron anchor profile or prime as recommended by Rawlins
Refer to the specific primer's product data sheet for substrate preparation requirements

Phosphatised Steel

Remove all contaminants per SSPC-SP 1

Application Methods

Product Information
Mixing:	Power mix separately, then combine and power mix thoroughly
Thinning:	Not normally required. Can be reduced up to 6 oz/gal with the following: Thinner 236 E Thinner 10 Thinner 76 For warmer temperatures use Thinner 214 or Thinner 25. Use of thinners other than those supplied or recommended by Carboline may adversely affect product performance and void product warranty, whether expressed or implied
Ratio:	2:1 Ratio (A to B)
Pot Life:	1.5 hours at 24 °C and less at higher temperatures. Pot life ends when coating becomes too viscous to use. Moisture contamination will shorten pot life and cause gellation
Conventional Spray:	Pressure pot equipped with dual regulators, minimum 3/8" I.D. material hose, 0.070" I.D. fluid tip and appropriate air cap
Airless Spray:	Pump Ratio: 30:1 (min.) Volume Output: minimum 2.5 gpm (9.5 l/min.) Airless Hose: 3/8" I.D. (min.) Tip Size: 0.013-0.017" Output PSI: 1,700-2,300 Filter Size: 60 mesh PTFE packings are recommended and available from the pump manufacturer
Brush and Roller:	Recommended for small areas or touch-up only Multiple coats may be required to obtain desired appearance, recommended dry film thickness and adequate hiding. Avoid excessive re-brushing or re-rolling For best results, tie-in within 10 minutes at 24 °C

Application Conditions

Product Conditions
Condition	Material	Surface	Ambient	Humidity
Minimum	4°C	2°C	2°C	0%
Maximum	32°C	60°C	43°C	95%

Industry standards are for substrate temperatures to be 3°C above the dew point
This product simply requires the substrate to be above the dew point
Caution: this product does react with atmospheric moisture to complete final cure
Relative humidity below 30% will slow cure time

Health and Safety

Clean Up

Use Thinner 2 or Acetone
In case of spillage, absorb and dispose of in accordance with local applicable regulations

Safety

Read and follow all caution statements on this product data sheet and on the safety data sheet for this product and use personal protective equipment as directed

Ventilation

When used in enclosed areas, thorough air circulation must be used during and after application until the coating is cured.
The ventilation system should be capable of preventing the solvent vapor concentration from reaching the lower explosion limit for the solvents used
User should test and monitor exposure levels to ensure all personnel are below guidelines
If not sure or if not able to monitor levels, use MSHA/NIOSH approved supplied air respirator

Refer to the product data sheet and safety data sheet in the attachments section above for further details

Product Details

Reference CRO4860

Data sheet

Interior / Exterior Use: Exterior
Water / Solvent Based: Solvent
Sheen: Gloss
Pack Size: 0.75 US Gallon Kit, 3 US Gallon Kit
Base Type: Aliphatic Polyaspartic
Minimum Applied Thickness: 6 mils
Maximum Applied Thickness: 10 mils
Mixing Ratio: 2:1
Key Features: Provides excellent corrosion protection and long term weatherability in just one coat.
Coverage: 4.6 m²/l at 150 microns
Recommended Thinner/Cleaner: Use Thinner 2 or Acetone.
Unit Contents: Part A & Part B
Compatible Primers: Carbozinc 11 Series; Carbozinc 608 HB; Carbozinc 621 with recoat window of 2 to 4 hours at 75 °F; Carbozinc 8701 with overnight cure; Carboguard 60 Series; Carboguard 61; Carboguard 635 Series; Carboguard 890 or CG 8922 Series.
Max. Application Temperature: 60°C
Min. Application Temperature: 2°C
Solids by Volume: 70% +/- 2%
VOC: 2.05 lbs/gal/246 g/l (varies by colour)
Shelf Life (from date of manufacture): 24 months (at 24 °C)
Size: -
Recommended Dry Film Thickness: 6 - 10 mils (152 - 254 microns) per coat; Can be applied at 4-5 mils DFT (102-127 microns) when applied over approved primer(s).
UN Number (Activator): UN1263
UN Number (Base): UN1263
Dry to Handle (at 10°C): 7 Hours
Dry to Recoat (at 10°C): 7 Hours
Fully Cured (at 10°C): 7 Days
Touch Dry (at 10°C): 2 Hours
Pot Life: 1.5 hours at 24 °C

Attachments

Download

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Send us your question

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

Carboline Carboquick 200 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT

Carboline Carboguard 60

Carboline Carboguard 60 is a high solids and abrasion resistant coating which can be used as a primer, intermediate coat, or self-priming finish over steel or inorganic zinc primers. May be topcoated with itself, or a broad variety of high-performance finish coats.Low odour and low VOC Good chemical resistance Fast cure and dry times...

£309.60 (incl. VAT)

£258.00 (ex. VAT)

COVERAGE CALCULATOR
Units
Film Thickness
Total area²
Or enter length and width dimensions:
Length
Width

Carboline Carboquick 200

Carboline Carboquick 200

Product customisation

Click To Jump To Section:

Features and Benefits

Product Specification

Drying Times

Surface Preparation

Application Methods

Application Conditions

Health and Safety

Data sheet

Question about the product

IMPORTANT SHIPPING & DELIVERY INFORMATION