Zingaceram HS (Formerly Zingaceram EP MIO HS), a high solid 2 pack intermediate coat to be applied as a sealer over Zinga. The coating has been used on both structural steelwork (for multi-million pound projects) and on sub-sea pipelines.
2 pack system
Seals Zinga with good compatibility
Apply by brush, roller, conventional sprayer or by airless spraying
High solid content & high chemical resistance
Dry to handle in 6 hours; fully cured in 18 hours
Temperature resistance of dry film: 95-100°C with peak up to 120°C
Zingaceram HS (Formerly Zingaceram EP MIO HS) is a high solid 2 pack intermediate coat to be applied as a sealer over Zinga by brush, roller or sprayer, with very good abrasion resistance and excellent corrosion protection properties. Its high solid (HS) content shows good compatibility on Zinga and has been used on both structural steelwork (for multi-million pound projects) and on sub-sea pipelines.
Features
2 pack system
Seals Zinga
Apply by brush, roller, conventional sprayer or by airless spraying
High solid content & high chemical resistance
Dry to handle in 6 hours; fully cured in 18 hours
Temperature resistance of dry film: 95-100°C with peak up to 120°C
pH resistance: 2,5 pH to 13 pH
Application
For more specific and detailed recommendations concerning application, please contact our technical team on 0113 2455450. For detailed information about the health and safety hazards and precautions for use, refer to the safety data sheet in the attachments tab above.
Brush or Roller
For optimal use, dilute Zingaceram up to 5% (v%) with HS Thinner
Use an industrial round brush or short hair roller (mohair)
Conventional Spray Gun
Dilution 10-15% (v%) with HS Thinner depending on nozzle size.
More dilution for same nozzle size will give a smoother surface finish; which will increase the abrasion resistance of the Zingaceram HS layer.
Pressure at the nozzle 2 to 3 bar for a structured aspect; higher pressure for a smoother aspect.
Nozzle opening 3 mm for a structured aspect; smaller (2.2 to 2.5 mm) for a smoother aspect.
Airless Sprayer
Dilution 0-5% (v%) with HS Thinner depending on nozzle size.
More dilution for same nozzle size will give a smoother surface finish.
Pressure at the nozzle: 150-250 bar
Pump ratio: 45/1
Nozzle opening: 0.021 - 0.025 inch / 0.38 - 0.63 mm
For Application on Zinga
Mist (tie) coat
Application at least 6 hours after ZINGA is touch dry.
25-30 μm DFT (Dry Film Thickness; to be measured above the peaks of the roughness profile)
Diluted according to Data Sheet
Full coat
2 hours after touch dry of mist coat
DFT = specified DFT - 25-30 µm DFT
Diluted according to Data Sheet
Coverage
Theoretical coverage
For 60 μm DFT: 13 m²/L
For 120 μm DFT: 6.5 m²/L
Theoretical consumption
For 60 μm DFT: 0.077 L/m²
For 120 μm DFT: 0.15 L/m²
Drying Times
For 60 μm DFT at 20°C in a well-ventilated environment:
Dust proof: 3 hours
Dry to handle: 6 hours
Fully cured: 18 hours
Fully resistant: 7 days
Overcoating (with a topcoat)
Overcoatable after minimum 8 hours after touch dry.
Maximum overcoat time depends on environmental conditions. Maximum 3 days.
Recommended System
Tested according to ISO12944 in industrial zones with high humidity and aggressive environment (continuous condensation and high pollution) (C5 I) and in coastal zones and marine zones with high salinity (continuous condensation and high pollution) (C5 M) with high classification (Life expectancy > 15 years):
ZINGA 1 x 60-80 μm DFT + Zingaceram HS 1 x 120 μm DFT
ZINGA 1 x 60-80 μm DFT + Zingaceram HS 1 x 120 μm DFT + Zingaceram EP 1 x 60 µm DFT
ZINGA 1 x 60-80 μm DFT + Zingaceram HS 1 x 120 μm DFT + Zingaceram PU 1 x 60 µm DFT
Product Details
3822-476721
Data sheet
Manufacturer
Zinga
For Use By
Professional Use
Water / Solvent Based
Solvent
For Use On
Steel
Application Method
Brush, Roller, Conventional Air Spray, Airless Spray
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Zinga Zingaceram HS is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...