Zinga Aluspray

Aluspray, a finishing coat that improves the aesthetic of Zinga in a handy and economical 500ml aerosol spray can. Ideal for spot treatment on small areas and touching up HDG, metallisation or previously treated Zinga surfaces.

  • Efficient and solid
  • Aluminium colour (~RAL 9006: comparable to hot-dip)
  • Good resistance to mechanic shocks, abrasion and erosion
  • Minimum -40°C, maximum +150°C temperature resistance (dry film)
  • Can be applied on ferro-metals and (damaged) zinc surfaces
Colour
Size
Finish
£13.70
VAT excluded

£16.44 Tax incl.
Quantity

Description

Aluspray is a finishing coat for Zinga in a handy 500ml aerosol spray can, ideal for spot-application on small areas and touching up HDG, metallisation or previously treated Zinga surfaces. Based on aluminium flakes, Aluspray can be applied either without primer on an old, non-corroded hot-dip galvanisation or metallisation layer or as topcoat on top of ZINGA for better aesthetics with an aluminium finish.



Features


  • Convenient and economical 500ml spray aerosol can
  • For spot application on small areas and touching up
  • Aluminium colour (~RAL 9006: comparable to hot-dip)
  • Good resistance to mechanic shocks, abrasion and erosion
  • Efficient and solid
  • Minimum -40°C, maximum +150°C temperature resistance (dry film)



Surface Preparation


Aluspray can be applied on ferro-metals and (damaged) zinc surfaces. For optimal performance, the metal should first be degreased, preferably by steam-cleaning. Alternatively, the surface can be degreased using solvent (e.g. Zingasolv), but never use white spirit.

For optimal performance, clean to SA 2,5 (ISO 8501:2007). For non-critical (small) areas, cleaning to St 3 is sufficient (using a steel brush).



Application


Aluspray must be shaken thoroughly before application for a minimum of 30 seconds after liberating the balls, repeating every time the can is left unused for some time.

Keep the spray between 10 and 20 cm away from the substrate and move in a continuous speed from left to right. Repeat with a spray application from top to bottom.

Always apply 2 layers when overcoating with a new layer of Aluspray; apply the second coat 1 hour after touch dry.

Clean equipment or spills with Zingasolv.

For more specific and detailed recommendations concerning application, please contact our technical team on 0113 2455450. For detailed information about the health and safety hazards and precautions for use, refer to the safety data sheet in the attachments tab above.



Drying Times


For 40 μm DFT at 20°C in a well-ventilated environment:

  • Touch dry: 15 minutes
  • Dry to handle: 1 hours
  • Fully cured: 48 hours

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
16 other products in the same category:

International Intergard 1735

International Intergard 1735 is a high performance, low VOC, water borne two component epoxy with a high gloss finish. International Intergard 1735 is a tough, hard wearing chemically resistant epoxy finish suitable for most circumstances where the odour or emissions from solvent based coatings are unacceptable.

Price £92.53
In stock

International Interthane 870

International Interthane 870 is high build which means it can reduce the number of coats you require and keep costs to a minimum. Semi-gloss and available in a range of colours, International Interthane 870 delivers excellent cosmetics and extended recoatability in both new construction and as an industrial maintenance.

Price £101.78
In stock

Tor Farm Oxide Semi-Gloss

Tor Farm Oxide Semi-Gloss is a general purpose finish with low toxicity, for use on and around farms and in farm buildings on a variety of substrates, including bare wood, steel and masonry. Modified alkyd resin binder pigmented with low toxicity pigments and extenders, thinned with low aromatic white spirit. Contains no lead pigments...

Price £22.68
In stock

Blackfriar Aluminium Paint

Blackfriar Aluminium Paint is heat resistant up to 150ºC and provides long-lasting, heat-resistant protection for interior and exterior surfaces, for use on metal and wood, on surfaces including car wheels, gates, railings, pipework etc.

Price £19.67
In stock

Sherwin-Williams Kem-Kromik 530

Kem-Kromik 530 (formerly known as Sherwin-Williams C530 or as Leighs C530) is a high quality, quick drying, lead free single pack alkyd gloss finish for interior and exterior surfaces, ideally suited for equipment manufacturers and for structural steelwork. Kem-Kromik 530 possesses excellent gloss and colour retention and outstanding...

Price £82.05
In stock

Jotun Hardtop Pro

Jotun Hardtop Pro is a low VOC, high volume solids, isocyanate free, economical polysiloxane topcoat for offshore structures, tank farms, refineries, power plants, bridges and buildings. It has very good colour and gloss retention and has very good resistance to abrasion and chemicals.

Price £102.42
In stock

Cromadex 635 Two Pack Polyurethane Leatherette Topcoat

Cromadex 635 Two Pack Polyurethane Leatherette Topcoat is a two pack polyurethane leatherette topcoat with excellent exterior durability and chemical resistance. The product exhibits excellent colour retention adding value to the finished article, whilst the leatherette effect can help differentiate your finish. Available in the full Cromadex range of...

Price £185.15
In stock

Jotun Hardtop Smart Pack

Jotun Hardtop Smart Pack is a two component chemically curing modified acrylic coating that does not contain isocyanates. It has a gloss finish with good gloss retention and can be used direct to metal. It has a 1:1 mixing ratio for easy use and reduced wastage and is specially designed for application with brush and roller.

Price £111.79
In stock

Cromadex 740 Two Pack Epoxy Fine Texture Topcoat

Cromadex 740 Two Pack Epoxy Fine Texture Topcoat is a two pack epoxy fine texture topcoat with excellent chemical resistance suitable for interior use only. The product offers a fine texture appearance for an aesthetic finish. The product can be air dried or stoved enabling flexibility in production. Available in a wide range of colours and gloss levels,...

Price £232.54
In stock

Carboline Carbomastic 242

An aluminium-pigmented, low temperature curing mastic for steel, designed for cold weather applications down to 0 °F (-18 °C). This unique coating provides excellent corrosion resistance over existing finishes and rusted or SSPC-SP2 or SP3 cleaned steel. Top Features Single coat application characteristics Suitable as a topcoat VOC...

Price £295.50
In stock

Teamac Rapidry QD Enamel

A fast drying industrial gloss finish, giving a good durable, protective coating to metal surfaces primed with Teamac Rapidry High Build Zinc Phosphate Primer or similar.

Price £15.40
In stock