HMG Thinner 2600
HMG Thinner 2600 is a very fast thinner.For use in recommended HMG systems.More Information Delivery Info
£47.71 (incl. VAT)
£39.76 (ex. VAT)
HMG Acrythane XSC21 Clear is a premium quality, high solids 2K Acrylic cured with isocyanate hardener with outstanding properties.
This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:
2-Pack System Details | |||
---|---|---|---|
Base (Part 1) | HMG Acrythane XSC21 Clear | ||
Hardener (Part 2) | HMG Hardener 9044 |
HMG Acrythane XSC21 Clear is a premium quality, high solids 2K acrylic cured with isocyanate hardener with outstanding properties.
Please note this product is one part of a two-pack system which MUST be purchased/used together with HMG Hardener 9044.
Technical Data | ||||
---|---|---|---|---|
Volume Solids: | 51.0% | |||
VOC Content: | 0.560kgs/ltr | |||
SG: | - | |||
Viscosity: | 350 mPas | |||
Density: | 1.02 g/cm³ | |||
Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed. | |||
Shelf Life: | 12 months from delivery date in original sealed containers. | |||
Pot Life: | 1 - 2 hours @ 20°C | |||
Flash Point: | 25°C |
Product Data | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | ||
Pressure Pot: | 40 μm | 80 μm | |
Compliant Spray Gun: | 40 μm | 80 μm |
Coverage: 12 square metres per litre @ 40 microns dft (theoretical)
Drying Times At 20°C | |
---|---|
Touch Dry: | 60 - 90 minutes |
Dry To Recoat: | After through curing (8 hrs @ 20°C / 30 mins @ 70°C), denib with P500g dry. After baking allow to cool before flatting & recoating. |
Fully Cured: | 8 hours |
Technical Data | |||||
---|---|---|---|---|---|
Compliant Spray Gun | Pressure Pot | ||||
Mixing Ratio: | Base: 2 | Base: 2 | |||
Hardener: 1 | Hardener: 1 | ||||
Thinner: 0.5 | Thinner: 0.5 | ||||
Hardener Options: | Hardener 9044 | Hardener 9044 | |||
Thinner Options: | Thinner 2600 | Thinner 2600 | |||
Thinner 2601 | Thinner 2601 | ||||
Thinner 2602 | Thinner 2602 | ||||
Thinner 2603 | Thinner 2603 | ||||
Thinner 2604 | Thinner 2604 | ||||
Viscosity: | 21 - 26 seconds B4 cup | 21 - 26 seconds B4 cup | |||
Spray Gun Setup: | 1.1 - 1.4 | 1.6 - 1.8 | |||
Number Of Coats (Guide Only): | 1 medium + 1 full | 1 medium + 1 full | |||
Flash Off: | 10 - 15 minutes | 10 - 15 minutes |
For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]
Information on basic physical and chemical properties | ||||
---|---|---|---|---|
Form: | Liquid | |||
Colour: | Clear | |||
Odour: | Characteristic | |||
Odour Threshold: | Not determined | |||
pH-value 20°C: | Not determined | |||
Melting point/freezing point: | Undetermined | |||
Initial boiling point and boiling range: | 126°C | |||
Flash Point: | 25°C | |||
Flammability (solid, gas): | Not applicable | |||
Ignition temperature: | 315°C | |||
Decomposition temperature: | Not determined. | |||
Auto-ignition temperature: | Product is not selfigniting | |||
Explosive properties: | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." | |||
Explosion limits: Lower: | 3.0 Vol % | |||
Explosion limits: Upper: | 10.4 Vol % | |||
Vapour pressure at 20°C: | 10.7 hPa | |||
Density at 20°C: | 1.02 g/cm³ | |||
Relative density: | Not determined | |||
Vapour density: | Not determined | |||
Evaporation rate: | Not determined | |||
Solubility in / Miscibility with water: | NOT MISCIBLE | |||
Partition coefficient: n-octanol/water: | Not determined | |||
Viscosity: Dynamic at 20°C: | 350 mPas | |||
Viscosity: Kinematic: | Not determined | |||
Solvent content: Organic solvents: | 43.5% | |||
Solids content: | 51.0% |
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
HMG Acrythane XSC21 Clear is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
HMG Thinner 2600 is a very fast thinner.For use in recommended HMG systems.More Information Delivery Info
£47.71 (incl. VAT)
£39.76 (ex. VAT)
HMG Thinner 2601 is a very fast thinner.For use in recommended HMG systems.More Information Delivery Info
£13.99 (incl. VAT)
£11.66 (ex. VAT)
HMG Thinner 2602 is a medium slow thinner.For use with compatible HMG systems.More Information Delivery Info
£14.05 (incl. VAT)
£11.71 (ex. VAT)
HMG Thinner 2603 is a medium slow thinner.For use with compatible HMG systems.More Information Delivery Info
£47.71 (incl. VAT)
£39.76 (ex. VAT)
HMG Thinner 2604 is a slow thinner.For use with compatible HMG systems.More Information Delivery Info
£14.69 (incl. VAT)
£12.24 (ex. VAT)
HMG 2K Accelerator is a hardener designed to speed up drying times.For use with HMG Acrythane systems.More Information Delivery Info
£39.74 (incl. VAT)
£33.12 (ex. VAT)
HMG Hardener 9044 is a medium solids isocyanate hardener. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:2-Pack System DetailsBase (Part 1) Option 1: HMG Acrythane XSC21Option 2: HMG Acrythane XSC21 ClearActivator (Part 2) HMG Hardener 9044...
£29.64 (incl. VAT)
£24.70 (ex. VAT)
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...
£25.84 (incl. VAT)
£21.53 (ex. VAT)