Contains all of the products and application tools required to ensure a high quality finish on uPVC windows, doors, fascias, and composite doors.
Technispray Kolorbond Aquatek is a water-based, low-odour, quick-drying exterior and interior coating for PVCu (uPVC). Available here in Anthracite Grey (RAL 7016) (looking for a lighter or darker grey? Pick one of our 12 trending shades of grey here) and also available in 2400+ colours from British Standard, NCS and RAL with an attractive smooth, satin finish. Can also be colour matched to nearly any colour.
Kolorbond uPVC Painting Kits are designed around Kolorbond Aquatekpaint and contain all of the products and application tools required to ensure a high quality smooth, satin finish on uPVC windows, doors and fascias. It is also suitable for use on composite doors.
Available in 4 pack sizes to suit the size of your project, please see `Paint Kit Contents`.
Technispray Kolorbond Aquatek is a water-based exterior and interior coating based on proven exterior durable polyurethane/acrylic resins, this single pack (mono-component) finish for PVCu (uPVC), is available in 2400+ colours from NCS, British Standard and RAL, and gives an attractive smooth, satin finish.
Ideally formulated to be brush applied, especially applicable for site application on refurbishment projects, domestic & commercial applications.
Based on exterior durable polyurethane/ acrylic resins, and utilising proven light fast pigments, the coating will give excellent exterior weathering properties, and has been tested in accordance with BS EN ISO4892-3: 2006 (QUV Test) using Lamp Type UVA351 accelerated weathering for 1600 hours.
In addition the applied coating exhibits good adhesion to the correctly prepared substrate and good hardness and scratch resistance. The coating is also supple and will not crack if the substrate bends.
4 x Lint free cloths (2 for applying Vinylkleen and 2 for applying Windowprep)
1 x Good quality synthetic 1.5 inch paint brush
PPE requirements (not included in packs):
Eye/face protection - Wear chemical splash goggles
Hand protection - Wear protective gloves made of the following material
Rubber (natural, latex)
Other skin and body protection - Wear appropriate clothing to prevent any possibility of skin contact
Respiratory protection - Wear a respirator fitted with the following cartridge: Organic vapour filter
Refer to Material Safety Data Sheets for each product for full details.
If you are brush applying Kolorbond Aquatek you will require disposable gloves and possibly protective clothing. A face mask is not necessary but essential if you decide to spray apply (the mask will require a particulate filter).
To reduce the chance of over painting it is a good idea to apply a layer of masking tape on glass and other adjoining substrates.
Before starting to clean the surfaces to be painted, dilute the Vinylkleen, one part to three parts water. Thoroughly clean the surface using the diluted Vinylkleen on one of the cloths provided. Keep turning the cloth as it becomes dirty.
Now thoroughly clean again using a second cloth with Windowprep on it. This will remove any remaining contaminants and any dust produced earlier. Again, turn the cloth as it becomes dirty. Windowprep contains alcohols so please wear gloves to protect your skin from drying.
Now lightly rub over all surfaces to be painted with the red abrasive pad. This will dull the surface but should not leave any scratch marks. If you are painting over wood grain foil, be careful not to rub too hard which can damage the wood grain finish.
When everything is dry you are ready to start painting. Firstly, stir the paint making sure that you stir right to the bottom of the can so that any settled colourants are fully mixed back in. Do not stir too vigorously as you do not want to create bubbles in the paint.
Apply the paint using the brush provided of a good quality synthetic brush. For roller application you must add up to 20% KolorFlow (not supplied) to the paint. (KolorFlow slows the drying of the paint, so can also be used to keep a wet edge when brushing or to prevent the paint from drying too fast on a hot day).
Brush on the paint in a nice even coat. Do not apply too much paint and then try to ‘work’ it. This paint dries too quickly and you can damage the finish.
When the paint is dry, after about 15 minutes, apply a second even coat being careful not to leave deep brush marks.
If you have a break during painting, make sure that you put your brush into water straight away. Should you allow the paint to dry on the brush you will have to throw the brush away. You will not get the dried paint off.
Although Kolorbond Aquatek dries very quickly it take up to a week to fully cure so please treat it gently for the first few days. If you have an area you want to cure quickly you can apply hot air from a domestic hairdryer once the paint is totally dry. Do not, of course, get the paint too hot or you could damage it.
On finishing painting, immediately wash out your brush and any other equipment with plenty of water.
NOTE: When prepping and painting, as described above, you should always use the correct protective equipment to protect your eyes, skin, respiratory tract and cloths etc. i.e. protective gloves, eye protection, clothing covering and respiratory masks fitted with organic vapour filters.
Always ensure that your working area is sufficiently ventilated.
Please read technical and safety data sheets before commencing.
For Use By
For Use By
Water / Solvent Based
For Use On
uPVC, Hard Plastics, Powder Coatings, GRP, Wood, Composite Doors
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Kolorbond uPVC Painting Kits - Anthracite Grey is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
Kolorbond WindowPrep is an alcohol based cleaner for use on PVCu prior to painting. It is very important that PVCu (uPVC) is cleaned with WindowPrep prior to painting; WindowPrep not only removes contaminants but also removes plasticizers from the surface of the PVCU and, additionally, opens the pores of the PVCu which greatly assists adhesion...
Kolorbond Aquatek, a water-based, low-odour, quick-drying exterior and interior coating for PVCu (uPVC), hard plastics (including polyester powder coatings), GRP composite doors and primed MDF and wood available in 5,000+ colours, inc. RAL Classic, BS, NCS & the new NCS 2050 colours with an attractive satin finish. Can be colour matched to...
Kolorbond VinylKleen is a water based cleaner for use on PVC and PVCu which removes water soluble contaminants and some silicones and oils. VinylKleen should be the first cleaner used before further cleaning with Kolorbond WindowPrep or Kolorbond VinylPrep. VinylKleen comes in a concentrated form and should be mixed 1 part VinylKleen with 3...
Kolorbond KolorFlow, for use with Kolorbond Aquatek to avoid leaving brush marks or to keep a ‘wet edge’ on a warm day.
Stir in 10% of KolorFlow (maximum 20%). This will slow the drying of the paint and assist leveling. The addition of KolorFlow also assists when spraying in hot weather.
More Information Delivery Info