Bonded and unbonded polymer modified granolithic screed and screed repair used to lay new granolithic screeds as thin as 15mm for heavy duty bonded application.
Ronafix Pre-packed Wearing Screed 15mm+ is supplied as a pre-packed, two component, ready to use mortar for laying floor screeds. Ronafix Pre-packed Wearing Screed 15mm+ is supplied complete with all the correct dry components in a bag and a bottle of polymer gauging liquid. Ronacrete Standard Primer two part polymer cement bonding agent is required for bonded screed applications.
Ronafix Pre-packed Wearing Screed 15mm+ is used to lay new granolithic screeds as thin as 15mm for heavy duty bonded application. Excellent adhesion can be achieved to suitably prepared surfaces and the screed is resistant to water, frost, and to heavy wear. The use of granolithic floating and unbonded screeds is uncommon and advice should be sought from Rawlins Technical Department on 0113 2455450 (option 2) or send a message to [email protected].
The substrate to which Ronafix Pre-packed Wearing Screed 15mm+ is to be bonded must be structurally sound and stable. Minimum compressive strength should be 25N/mm2 and minimum pull-off strength should be 1.5N/mm2.
Surfaces should be vacuum shot blasted, planed or scabbled to expose aggregate, remove laitance and provide a mechanical key. All grease and oil must be removed.
Dust, debris and loose material must be removed by vacuuming. Any defect or weakness in the substrate may result in failure of the topping or screed applied to it.
The recommendations given in BS8204-3 section 7 should be followed, to assess the suitability of the substrate and ensure the performance of the topping. When repairing concrete with Ronafix Pre-packed Wearing Screed 15mm+, repair perimeters must be saw cut and the concrete scabbled as required, to allow the minimum depth of mortar to be placed throughout.
The prepared surfaces must be thoroughly wetted with clean water.
Very porous surfaces may require soaking for up to 24 hours.
All surplus water must be removed before the primer is applied.
Brush apply a coat of Ronacrete Standard Primer to the damp surface immediately before applying Ronafix Pre-packed Wearing Screed 15mm+.
Mix the primer thoroughly and apply evenly over the surfaces ensuring total and uniform coverage taking care to avoid ponding. Only prime an area of floor which can be covered by the mortar within the working time of the primer.
The coverage rate of Ronacrete Standard Primer is 1.5-2m² per kg. Note that the primer must not be allowed to dry. Dry primer must be thoroughly abraded and reapplied.
Ronafix Pre-packed Wearing Screed 15mm+ must be mixed by forced action mixer (e.g. CreteAngle, Baron or similar) or high powered, slow speed drill and suitable spiral paddle (MR4 or similar) for approximately 3 minutes, shorter mixing times will not fully disperse the components and workability will be reduced. Free fall mixers must not be used.
Once mixed the mortar should be used as quickly as possible.
As soon as the mortar is mixed, it should be applied to wet/tacky primer, fully compacted, ruled and closed with a float or trowel. Avoid overworking the surface, this will increase the tackiness of the mortar.
The float should be regularly washed, to prevent build up of polymer/cement paste.
Joints should be formed in the floor screed/topping in line with movement joints and bay joints; on suspended floors, joints should be positioned over slab supports to accommodate movement.
For further information refer to BS8204-3. It is unlikely that the desired finish to a granolithic screeds will be achieved during laying.
To obtain an acceptable finish to a granolithic screed, the screeder may need to return to the hardening screed on at least one occasion for further trowelling.
As soon as possible after finishing the surface, cure with Ronacrete Curing Membrane.
Alternatively use tight fitting polythene, to be left in place for at least 24 hours, to prevent rapid moisture loss from the surface.
The use of Ronacrete Curing Membrane is preferred, because curing may commence immediately after trowelling is complete. Early application of curing membrane is particularly important when the surface is exposed to sunlight and/ or drying winds.
Ronafix Pre-packed Wearing Screed 15mm+, toppings and repairs can typically receive foot traffic after 24 hours and heavy traffic after 3-5 days at 200°C. Allow more time in cold conditions.
Floor finishes, including resilient flooring, tiles and resin coatings/ screeds may typically be laid after 10 days air curing at 50mm thickness, 200°C and 60-65% relative humidity.
Measure screed RH with a hygrometer in accordance with Annex A (normative) of BS 8203 Dampness testing.
Ronafix Pre-packed Wearing Screed 15mm+ can be used in most weather conditions and in a wide temperature range, typically from 5°C to 25°C.
Note that at high ambient temperatures the working time of the mix will be reduced; it will be increased at lower temperatures.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Ronacrete Ronafix Pre-Packed Wearing Screed 15mm+ is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Pre-packed polymer modified bonding primer.Conforms to BS EN 1504-4 Comprises polymer liquid and specially graded cements Used to provide a chemical bond between the substrate and new surfacing Only to be used with Ronacrete’s mortars and concretes including:RonaBond HB40 RonaBond HB25 RonaBond Concrete Repair Mortar Ronafix...
£12.92 (incl. VAT)
£10.77 (ex. VAT)
Spray applied curing membrane for mortars and concrete repair, flooring and renders, foming a surface barrier slowing the rate of moisture loss.Reduces chances of cracking Supplied ready to use Good coverage - 5.0-6.5m2 per litre Ronacrete Curing Membrane - For professional and industrial useMore Information Delivery Info
£18.74 (incl. VAT)
£15.62 (ex. VAT)
