PPG Thinner 90-53
This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info
£42.59 (incl. VAT)
£35.49 (ex. VAT)
PPG SigmaGuard CSF 585 is a two-component, solvent-free, amine-cured epoxy tank coating for the storage of drinking water (approved by KIWA Holland) up to 60°C (140°F), for use with SIGMACOVER 522 primer. The coating meets NSF/ANSI Standard 61 for potable water when applied and used as described on nsf.org/
PPG SigmaGuard CSF 585 is a two-component, solvent-free, amine-cured epoxy tank coating for the storage of drinking water (approved by KIWA Holland) up to 60°C (140°F), for use with SIGMACOVER 522 primer. The coating meets NSF/ANSI Standard 61 for potable water when applied and used as described on nsf.org/
SigmaGuard CSF 585 has reduced fire hazard and explosion risk, with good visibility in confined spaces due to its light colour.
Reference | Colour | Size | Gloss Level |
---|---|---|---|
219195 | Blue | 4 litres | Gloss |
219191 | Blue | 20 litres | Gloss |
- | White | 20 litres | Gloss |
Two-component, solvent-free, amine-cured epoxy coating
Data for mixed product at 20°C (68°F) | |
---|---|
Number of components | Two |
Mass density | 1.3 kg/l (10.8 lb/US gal) |
Volume solids | 100% |
VOC (Supplied) | Directive 1999/13/EC, SED: max. 5.0 g/kg |
max. 6.0 g/l (approx. 0.1 lb/US gal) | |
EPA Method 24: 3.4 g/ltr (0.0 lb/USgal) | |
Recommended dry film thickness | 250 - 400 µm (10.0 - 16.0 mils) depending on system |
Theoretical spreading rate | 3.3 m²/l for 300 µm (134 ft²/US gal for 12.0 mils) |
Pot life | 90 minutes at 20°C (68°F) |
Dry to touch | 5 hours |
Overcoating Interval | Minimum: 24 hours |
Maximum: 20 days | |
Full cure after | 12 days |
Shelf life | Base: at least 24 months when stored cool and dry |
Hardener: at least 24 months when stored cool and dry |
Notes:
Recommended Substrate Conditions and Temperatures
Substrate conditions
Carbon steel
Concrete
Substrate Temperature & Application Conditions
Instructions for Use
Mixing ratio by volume: base to hardener 77.5:22:5
Induction Time
Mixed product induction time | ||
---|---|---|
Mixed product temperature | Induction time | |
10°C (50°F) | 15 minutes |
Airless spray
Recommended thinner
Nozzle orifice
Nozzle pressure
At 20°C (68°F) paint temperature min. 28.0 MPa (approx. 280 bar; 4061 p.s.i.). At 30°C (86°F) min. 22.0 MPa (approx. 220 bar; 3191 p.s.i.)
Note:
In case of using 45:1 airless spray equipment, the paint must be heated to approximately 30°C (86°F) in order to obtain the right application viscosity
Brush/roller
Recommended thinner
Cleaning Solvent
Note:
All application equipment must be cleaned immediately after use. Paint inside the spraying equipment must be removed before the pot life has been expired.
DFT | Theoretical spreading rate |
---|---|
250 µm (10.0 mils) | 4.0 m²/l (160 ft²/US gal) |
300 µm (12.0 mils) | 3.3 m²/l (134 ft²/US gal) |
400 µm (16.0 mils) | 2.5 m²/l (100 ft²/US gal) |
Note:
Measuring wet film thickness
Measuring dry film thickness
Overcoating interval for DFT up to 300 µm (12.0 mils)
Overcoating with... | Interval | 10°C (50°F) | 20°C (68°F) | 30°C (86°F) | 40°C (104°F) |
---|---|---|---|---|---|
Itself | Minimum | 4 days | 24 hours | 16 hours | 10 hours |
Maximum | 28 days | 20 days | 14 days | 14 days |
Notes:
Curing time for DFT up to 300 µm (12.0 mils)
Substrate temperature | Dry to handle | Full cure |
---|---|---|
10°C (50°F) | 4 days | 20 days |
20°C (68°F) | 24 hours | 12 days |
30°C (86°F) | 16 hours | 7 days |
40°C (104°F) | 10 hours | 5 days |
Notes:
Washing procedures
Example 1: Adequate washing procedure
Example 2: Adequate washing procedure
Pot Life (at application viscosity)
Mixed product temperature | Pot life |
---|---|
20°C (68°F) | 1.5 hours |
30°C (86°F) | 1 hours |
Note:
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
PPG SigmaGuard CSF 585 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info
£42.59 (incl. VAT)
£35.49 (ex. VAT)
This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info
£134.09 (incl. VAT)
£111.74 (ex. VAT)
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...
£25.84 (incl. VAT)
£21.53 (ex. VAT)