Tikkurila Fontefire ST60 is a water-borne, one-component intumescent paint formulated for the fire protection of structural interior steel elements.
Its protecting effect is based on a strong heat expansion binding reaction that results in the creation of an insulating foam layer. Even a thin film thickness provides excellent fire protection properties.
A fast-drying, one-component, semi-gloss alkyd topcoat, containing anti-corrosive pigments
approx. 50-60 µm
Application:
Application by brush, roller, or airless spray
Mix the paint thoroughly before use
Recommended dry film thickness is approximately 500 µm/layer
Diameter of the paint hoses should be at least 10mm, the length should not exceed 60m
Nozzle tip size 0.019"–0.025", turnable nozzle is recommended
Nozzle shall be chosen according to the efficiency and output of the equipment
Nozzle pressure 175–210 kg/cm2. Spray angle shall be chosen according to the shape of the object
Control of Film Thickness:
Application with roller and brush is typically 416 µm WFT (300 µm DFT)
Before overcoating should the dry film thickness of the coating be controlled with a reliable test method in accordance with SFS ISO 19840 and a record should be drawn
Packing and Touch-Up of Damages:
Components painted in workshop should be covered with a plastic film during transport and storage and packed to avoid impresses
During winter season components should be dried 48 hours in room temperature before taken outdoors
Damages shall be repaired immediately in the same way as originally
Thinner:
Water
Cleaning of Equipment:
Water
Application Conditions
All surfaces must be clean, dry, and free from contamination
The temperature of the ambient air, surface and paint should not fall below +15ºC during application and drying
Relative humidity of the air should not exceed 80% during application and drying
The surface temperature of the steel should remain at least 3ºC above the dew point
Good ventilation and sufficient air movement is required in confined areas during application and drying
Health and Safety
Refer to the product data sheet and safety data sheet in the attachments section above for further details
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contactedto obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditionsand should be applied only by an individual with the necessary expertise and experience.We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Tikkurila Fontefire ST60 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
Tikkurila Fontecoat EP 50, a two-component water-borne epoxy topcoat and a single-coat paint recommended for framework, service platforms, conveyors and other steelwork, machinery and equipment. The product has MED (Marine Equipment Directive) certificate no VTT-C-12360-15-18 and is thus accepted for painting surfaces inside ships.Huge...
Tikkurila Fontecryl AP is a water-borne, one-component fast-drying acrylic based primer for various surfaces containing active anti-corrosive pigments.Provides excellent adhesion Used as an anti-corrosive primer on steel, aluminium and zinc surfaces Suitable for dipping Can be overcoated both with water and solvent-borne topcoats Wide...
Tikkurila Fontecryl SC 50 is a water-borne, one-component fast drying alkyd modified acrylic paint containing active anti-corrosive pigments. Used as a single-coat paint, it is also suitable as a topcoat for painting in metal industry and painting stations.Huge colour range available from RAL, BS & NCS High film-building properties...
Tikkurila Temacoat GPL-S Primer is a two-component, polyamide-cured high build epoxy primer containing zinc phosphate.Excellent adhesion to steel, zinc and aluminium surfaces. Used as a primer or an intermediate coat in paint systems exposed to abrasion and chemical stress. Can be overcoated after a prolonged period of time. Faster...
A two-component resin modified epoxy paint containing anti-corrosive pigments that can be applied at sub-zero temperatures as a primer or an intermediate coat on surfaces exposed to climatic, mechanical and chemical stress.Recommended for building frameworks, tubular bridges, conveyors and other steelwork and equipment Adheres well to...
Tikkurila Temadur 50, a time-proven, easy-to-use general purpose topcoat for constructional steelwork and machinery, with a wide range of colours to choose from.Two-component, durable and non-chalking semi-gloss polyurethane paint, hardener aliphatic isocyanate Forms a durable, easy-to-clean and non-chalking topcoat with good gloss and...
Tikkurila Temalac FD 50, a fast-drying, one-component semi-gloss alkyd topcoat, containing anti-corrosive pigments, that can be used as a single-coat system and a primer on steel surfaces. The paint is an ideal solution for workshops with fast production cycles and for painting stationsHuge colour range, including RAL, BS & NCS shades...
Tikkurila Temaprime EUR is a fast-drying, one-component anti-corrosive economical alkyd primer. Recommended for steel structures, agricultural, construction and other machinery.Huge colour range available. An excellent choice for use in assembling plants and painting stations with rapid production cycles. The product has MED (Marine...
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...