RSL Resuflor GC-UVR (formerly known as Resucoat GC and R.S Screed Seal) is a two-pack epoxy resin surface coating for use with other RSL and Sherwin-Williams products, filling any voids, pockets or interstices exposed in the surface.
For optimum results, RSL Resuflor GC-UVR (formerly known as Resucoat GC and R.S Screed Seal) should be used with Resuscreed 45, Resuscreed 55, and Resuscreed QS - all Resin Surfaces Limited products.
Recommended Uses
Food and beverage sites
Factories
Warehouses
Engineering environments
Garages/Showrooms
Aviation hangars
Preparation
The surface to be treated with Resuflor GC-UVR must be clean, sound, dry and fully cured. Rates of coverage will be affected by the particle size and the density of packing achieved during the application of the screed. Open textures will reduce rates of coverage significantly.
Application
The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance of the system. Surface temperature must be above 10°C.
Where possible it is recommended that the application area is heated to a minimum temperature of 15°C to allow the ambient and substrate temperature to stabilise prior to installation.
Mixing: Pre-mix the base component to a uniform consistency then mix the entire contents of the base with the hardener. If a separate mixing bucket is being used, mix thoroughly ensuring all contents of both components are removed from the buckets supplied. Mix using a slow speed electric mixer for approximately two minutes or until the two components have fully combined.
Resuflor GC-UVR is highly thixotropic, careful and thorough mixing is required. For trowel and squeegee application, de-nibbing of the surface by steel trowel is recommended prior to application.
Resuflor GC-UVR should be applied within 48 hrs of the application of the screed system. Apply to the clean surface with a polypropylene squeegee. Ensure that the Resuflor GC-UVR is forced into the surface of the resin screed and pull down any excess to leave a thin coating. Finally, roller off to achieve an even film finish. Resuflor GC-UVRdoes not tend to flow, therefore it is important to ensure that the finish is to an acceptable standard whilst wet.
When Resuflor GC-UVR is being used on coloured systems, after an overnight cure apply a coat of Resuflor HB to provide a wearing finish.
When Resuflor GC-UVR is being used on decorative systems, after an overnight cure apply a coat of Resuflor HB Clear to provide a wearing finish.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Resuflor Q Screed (formerly known as Resuscreed QS and Decora MS), is a decorative epoxy resin floor screed incorporating multi-coloured aggregates, designed to produce a hard wearing, attractive, impervious sealed surface, sealed with clear resins to provide a matt or gloss finish. More aggregate can be bought by adding RSL Resuscreed QS...
Resuflor Screed (formerly known as Resuscreed 45) is a heavy duty, epoxy resin floor screed which uses a crystalline silica free aggregate, making it more environmentally friendly. Must seal for an impervious finish.
Less dust than other screeds
Low odour
Hard wearing
Abrasion and impact resistant
Can form coving and falls
Can be...
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.
Resuflor HB Clear (formerly known as Resutop Clear) is a two-pack, high solids, high-build epoxy coating for application as a chemical resistant heavy duty floor coating, used as a clear sealer for decorative flooring systems such as Decora MS, producing a seamless, hard wearing, hygienic floor finish.
Low odour
Good colour stability...