RSL Resudeck ST

DESTB

RSL Resudeck ST (formerly Resudeck) is a two-pack polyurethane floor coating designed for wet environments and is hot water resistant. It also has a durable, flexible finish and is resistant to chemical attack. 

  • High-build
  • Hard-wearing
  • Solvent-free
  • Can be used on concrete, wood and asphalt
  • Anti-slip can be added
  • Resistance to many fuels and lubricants

Colour
  • Current colour: White
Choose a colour
Close colour picker
  • White
  • Black
  • RAL 3013 (RSL)
  • RAL 5010 (RSL)
  • RAL 5015 (RSL)
  • RAL 6001 (RSL)
  • RAL 7015 (RSL)
  • RAL 7042 (RSL)
  • RAL 7047 (RSL)
Size
Finish
£87.86
VAT excluded

£105.43 Tax incl.
Quantity

Description

RSL Resudeck ST (formerly Resudeck) is designed to combat wet environments, whilst offering anti-slip aggregates and light to medium chemical resistance. It can dry overnight in warm temperatures ready for footfall after just 24 hours.

It offers adhesion to asphalt and bituminous surfaces without even needing a primer. It comes in a variety of colours that cure to a gloss finish, and can be used in conjunction with zinc-based primers, such as Resuprime ZP, when treating metal surfaces.

Recommended Uses

  • Basement car parks exposed to water
  • Vehicle decks
  • Food areas - notably bakeries
  • Plant rooms

Preparation

New Concrete Floors: New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm sq. is required.

Existing Concrete Floors: Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue of detergent is washed and removed by rinsing with clean water. Local repairs should be carried out using Resuscreed PA or Resuscreed 45.

Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with existing floor coating.

Where Resudeck ST is applied to masonry/concrete surfaces, care must be taken to ensure that surface preparation is thorough but does not disfigure the surface.

Priming

Open and porous substrates may require priming with Resuseal WB, also Resuprime ST may be used as primer on the dry substrates only with less than 75% ERH reading.

Resuprime ZP should be used as a primer onto steel substrates where appropriate. Where the relative humidity of a substrate exceeds 75% ERH, Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.

The number of coats to be applied is chosen in accordance with the following table.

ERH% Required Coating Thickness
75-85 - 1 coat of Resuprime MVT at 200 microns per coat
85-92 - 2 coats of Resuprime MVT at 200 microns per coat
92-97 - 3 coats of Resuprime MVT at 200 microns per coat

For Further information please refer to recommended individual product data sheets.

Application

The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 5°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally to allow the ambient and substrate temperature to stabilise prior to installation.

Pre-mix the coloured base component to a uniform consistency then mix the entire contents of the base with the hardener. If a separate mixing bucket is being used mix thoroughly ensuring all contents of both components are removed from the buckets supplied. Mix using a slow speed electric mixer for approximately two to three minutes until the two components have fully combined.

The mixed unit should be applied immediately by squeegee, roller or brush with a consistent procedure. Floor areas should be cross-rolled to ensure even application and to minimise roller marks. Coverage rates may vary depending on profile and porosity of the substrate.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
DESTB

Data sheet

Manufacturer
RSL
For Use On
Concrete
Application Method
Brush, Roller, Squeegee
Sheen
Gloss
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Two-Pack
Pack Size
5L, 15L
Coverage
5 litres will cover 25m sq. @ 200 microns wet film thickness.
Touch Dry
6-8 Hours.
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

RSL Resuseal WB

Resuseal WB is a multi-purpose, two-pack, water-based epoxy coating primarily for concrete walls and floors. It can also be applied to concrete poured 7 days prior, as well as wood for a dust-free finish.  Low odour  Silica Free  Superb adhesion  Hard wearing  Hygienic Dust-free Some product colours are made to order and have minimum...

Price £50.53
In stock

RSL Resuprime ST

Resuprime ST (formerly known as Resuprime) is a two-pack, solvent-free epoxy resin bonding and priming coat. It bonds resin-based screeds and toppings to cementitious and other surfaces.  Features and Benefits: Versatile for many types of application Excellent adhesive properties Easy to apply Can be used as a tack coat for screeds No...

Price £68.19
In stock

RSL Resuscreed 45

Resuscreed 45 is a heavy duty, epoxy resin floor screed which uses a crystalline silica free aggregate, making it more environmentally friendly. Must seal for an impervious finish. ADVANTAGES Less dust than other screeds Low odour Hard wearing Abrasion and impact resistant Can form coving and falls Can be feather edged Can act as a...

Price £59.30
In stock

RSL Resuprime MVT

RSL Resuprime MVT (formerly known as R.S. Dampshield FH) is a faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood.  Features and Benefits:...

Price £19.80
In stock

RSL Resuscreed PA

RSL Resuscreed PA (formerly known as Resupatch) is a three-pack epoxy resin mortar designed for rapid concrete repair in heavy duty environments. Features and Benefits:  Excellent mechanical properties Can be feather edged Abrasion and impact resistant Dust-free Concrete like in appearance Easy to apply Minimum surface preparation

Price £38.44
In stock