Blackfriar Multi-Surface Primer has been specially formulated to prime multiple surfaces prior to further painting. It’s ideal for hard and soft woods, chipboard, plywood, GRP, MDF, exterior UPVC, ceramic tiles, iron, steel, galvanised and non-ferrous metals (aluminium, brass, chrome, copper) and old plaster. Product Features Interior and...
Blackfriar Aluminium Paint
Blackfriar Aluminium Paint is heat resistant up to 150ºC and rovides long-lasting, heat-resistant protection for interior and exterior surfaces. You can use it on metal and wood, on surfaces including car wheels, gates, railings, pipework etc.
- Extra bright finish.
- Heat resistant up to 150oC.
- Interior and exterior use.
- For metal and wood.
- Reflects heat from surfaces.
Blackfriar Aluminium Paint provides long-lasting, heat resistant protection for interior and exterior surfaces. For use on metal and wood. Ideal for car wheels, gates, railings, cycles, models, pipework and decorations. Its reflective finish effectively reduces temperatures on areas such as storage tanks and caravan roofs.
Ensure the surface to be painted is clean, dry, and free from grease, oils, wax or any other surface contamination. Remove any loose and flaking paint back to a firm feathered edge. Galvanised metal should be degreased and primed with Blackfriar Multi-Surface Primer.
Rusty metal should be wire-brushed to a clean, bright surface and primed immediately with Blackfriar Anti-Rust Metal Primer. New and bare surfaces should also be primed with an appropriate Blackfriar primer.
Stir paint well using a broad stirrer before and during use. Blackfriar Aluminium Paint may be applied by brush or spray. Apply 1-2 coats, as required.
Do not use under cold (less than 5°C), damp or humid conditions. Not suitable for direct application to galvanised metal, use Blackfriar Multi-Surface Primer first. Due to the bright metallic finish of this product, colour transfer may occur.
NB: The varnish may produce a yellowing effect.
Touch dry in 2 - 4 hours. Recoat after 16 hours and within 3 days. Drying times are based on an ambient temperature of 20°C and 50% relative humidity. Lower temperatures or higher humidity will prolong the drying and overcoating times.
Remove as much product as possible from application equipment before washing with white spirit. Do not empty into drains or water courses. Some local authorities have special facilities for the disposal of waste coatings.
Store in a dry, safe place. Do not store in environments where extreme temperatures may occur. Keep within 5-30°C. Do not store in direct sunlight.
- Heat-resistant to 150ºC/300ºF
- Reflects heat from surfaces
- Interior and exterior use
- For metal and wood
- Extra bright finish
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Blackfriar Professional
- Base Type
- Solvent Based
- Interior/Exterior Use
- Brush, Roller, Spray
- Dry to Recoat (at 20°C)
- 16 Hours
- 14m² per litre
- Recommended Thinner/Cleaner
- Do Not Thin/Cleaner White Spirit
- Min. Application Temperature
- Touch Dry
- 2-4 Hours
- UN Number
|Bernard Kelly on 2018-11-27 15:45:58|| |
Is it water based.
No, it is based on a blend of Hydrocarbon Resin with Linseed Oil Varnish media.
Blackfriar Polyurethane Varnish transforms interior woodwork. This tough and durable varnish brings out the natural grain and colours of wooden surfaces – and protects them from household stains including hot water. For all types of interior wood. It is tough and durable, resists hot water splashes and dilute acids and is solvent based....
Blackfriar Exterior Varnish Enhances and protects all wood and external joinery. It provides protection to all types of wood by resisting UV light to give your wood superior durability when applied over Blackfriar UV Wood Primer. It waterproofs as well as adding an attractive finish. Product Features Enriches and protects your home and...
Blackfriar Anti-Rust Primer is a rust inhibiting primer containing Zinc Phosphate for the protection of ferrous metals. Specifically formulated for painting metal surfaces to prevent corrosion. Recommended for use with Blackfriar Quick Drying Metal Paint. Product Features For ferrous metals. Interior and exterior use. Anti-corrosive....
HMG Coach Enamel is traditional, ultra high quality, high build, long oil synthetic enamel for brush application. It gives an extra long wet edge time allowing it to be brushed without brush drag. High gloss. Excellent water resistance. Flexible with good exterior durability and toughness. Available in a wide colour range including...
Cromadex 742 Two Pack Epoxy Medium Texture Topcoat is a two pack epoxy medium texture topcoat with excellent chemical resistance for interior use only. The product offers a medium texture appearance for an aesthetic finish. The product can be air dried or stoved enabling flexibility in production. Available in a wide range of colours and gloss...
Cromadex 233 One Pack Air Drying Alkyd Topcoat is a one pack air drying topcoat with a high level of full gloss adding value to the finished article. The product has a long wet edge that enables a seamless finish on large articles without dry spray. Available in the full Cromadex range of colours and gloss levels, including BS, RAL, metallic, sparkles and...
Bradite Fastrac is a high performance direct-to-metal silicone/polyurethane alkyd finish. Perfect for the protection and decoration of ferrous metals in many home projects such as fencing, gates and other ironmongery. Manufactured under the auspices of an ISO 9001:2008 & ISO 14001:2004 Available in more than 350 colours in RAL & BS...
Jotun Pilot II is a one component oxidatively drying alkyd coating from Jotun that has a gloss finish with good gloss retention. To be used as a topcoat in atmospheric environments. Jotun Pilot II is recommended as a topcoat, and for touch-up purposes for marine engines, topside, deck and superstructure areas and for a wide range of...
Cromadex 840 Two Pack Non-Isocyanate Acrylic Fine Texture Topcoat is a two pack non-isocyanate acrylic fine texture topcoat with excellent exterior durability and chemical resistance. The product uses unique resin and pigment technology enable a wide variety of applications and a durable finish, whilst the fine texture appearance offers an aesthetic finish.
Axalta ViterThane PLS Recoatable PU Finish, A two pack recoatable polyurethane semi-gloss finish for use on protective systems for steelwork. Excellent colour retention and indefinitely overcoatable. Excellent chemical resistance and low temperature cure. An aliphatic polyurethane providing a tough and durable semi-gloss finish with...
Tor Tractor Enamel, available in over 350 colours, is ideal for farm machinery, tractors, vehicles, tools and implements. The general purpose gloss enamel has a high flash point and applies to bare steel and previously-painted surfaces by brush, roller or conventional sprayer. Choose from 350+ colours in RAL and BS Good coverage - up to...
Zingatarfree (Formally PU Tarfree MIO) is ideal for marine environments and immersion, such boat hulls, with excellent water, corrosion and chemical resistance, and can be used as a replacement for normal coal tar products Single-pack polyurethane paint Use as part of a duplex system with Zinga Apply by brush, roller, conventional...
Cromadex 642 Two Pack Polyurethane Medium Texture Topcoat is a two pack polyurethane medium texture topcoat with excellent exterior durability and chemical resistance. The product offers a medium texture appearance for an aesthetic finish. Demonstrates good mar resistance, ideal if the end product is to be widely handled. The addition of Rapidcure can...
Cromadex AQ40 One Pack Waterbased Air Drying Topcoat is a one pack water based air drying topcoat with excellent gloss and colour retention adding value to the finished article. Available in the full Cromadex range of colours and gloss levels, including BS, RAL and special matches all in a lead free finish. Life expectancy of up to 3 years in a C2...
PPG Sigma Vikote 18 is a high-build, aluminum pigmented chlorinated rubber primer/sealer. Offering excellent water resistance, resistance to well-designed/controlled cathodic protection and can be applied at temperatures down to –10°C (14°F). Anti-corrosive primer/sealer Fast-drying Tolerates a DFT up to 150 µm (6.0 mils) at overlaps...
Jotun Hardtop XPF is a two component chemically curing aliphatic acrylic polyurethane coating that is fast drying and has a high solids content. It has a gloss finish with very good gloss retention and should be used as topcoat in atmospheric environments, it can also be applied at sub zero surface temperatures. Coverage Calculator
A high-build epoxy mastic coating used for atmospheric exposed and submerged steel. Top Features Excellent film build and edge protection Surface tolerant characteristics Cures at low temperature
This product is now only available with a minimum order of 800 litres; for smaller orders, we can recommend Jotun Pilot II as a great alternative. Jotun Alkyd Topcoat is a one component oxidatively drying alkyd coating. It has a gloss finish with good gloss retention and is to be used as topcoat in atmospheric environments. Generally used in...
Cromadex 440 One Pack Lower Odour Polyurethane Fine Texture Topcoat is a one pack lower odour topcoat that comes in a fine texture finish that adds value to your product. The product uses polyurethane technology providing excellent colour retention. The product has a long wet edge making it easier to apply to large items with no dry spray.