Wethertex MS11 Multi-Surface Renovation Paint is a high performance protective coating providing a decorative satin finish to multiple substrates for both interior and exterior application; is also self priming and resistant to flash rust.
Long-term protection - highly durable, highly breathable and water repellent
Excellent adhesion - quick drying - Self Priming
Advanced 10 year durability
Suitable for multiple surfaces including steel, PVC, uPVC, wood, brick and many more
Available in 4,350+ colours, inc. RAL, RAL Design, BS, NCS & the new NCS 2050 colours
Wethertex MS11 Multi-Surface Renovation Paint is a high performance protective coating providing a decorative satin finish offering long term protection with 10 year durability. It has superb adhesion to multiple substrates while being highly vapour permeable and water-shedding. This versatile, hard wearing paint for both interior and exterior application is also self priming and resistant to flash rust.
Wethertex MS11 Multi-Surface Renovation Paint offers long-term protection, is highly breathable and water repellent. It is suitable for multiple surfaces Steel, Aluminium, Galvanized steel, Ceramic tile (not showers/wet rooms), PVC, Wood, Brick, Concrete Block, Stone, Plaster, Pre-cast concrete, Render, Fibre cement board, Plaster boards, Calcium silicate boards and any surface where great adhesion, fast drying, good coverage is required.
Available in 4,350+ colours, inc. RAL, RAL Design, BS, NCS & the new NCS 2050 colours.
Long-term protection - Advanced 10 years durability
Highly breathable
Water repellent
Highly durable
Excellent adhesion
Quick drying
Suitable for multiple surfaces including steel, PVC, uPVC, wood, brick and many more
Aluminium
Block
Brick
Calcium Silicate Boards
Ceramic Tile (Excluding Showers/Wet Rooms)
Clay Block
Concrete
Dash Rendered Finish
Ferrous Metals
Fibre Cement Boards
Galvanised Steel
Lightweight Block
Non-Ferrous Metals
Plastisol
Pre-Cast Concrete
PVC
Roughcast / Wet Dash
Smooth Render
Steel
Stone
Well Bonded Coatings
Well Bonded Paint
Wethertex GRC Fibre Glass Reinforced Base Coat
Wethertex X71 Polymer Levelling Base Coat
Wood & Timber
Available in 4,350+ colours, inc. RAL, RAL Design, BS, NCS & the new NCS 2050 colours
Approximately 12 to 15m²/Litre per coat dependant on the nature and porosity of the surface. Rough surfaces will significantly reduce the coverage rates
Surface Preparation
Ensure all surfaces to be painted are clean, dry and free from grease, loose or flaking material and any other contaminants that may impair adhesion
Any faults in the substrate, particularly those that can lead to moisture penetration, must be rectified or can affect the finish quality
If your substrate has been previously painted rub down with a fine waterproof abrasive paper and then rinse thoroughly
Bare substrates should also be abraded in a similar manner to allow improved adhesion
To improve inter-coat adhesion, repeat between all additional coats
Hard wall plasters should be scored with a coarse glass-paper
Avoid the inhalation of dust
Wear a suitable face mask if dry sanding
Application
Apply by brush, roller, conventional H.V.L.P or airless spray
Stir well and check colour before use
Do not apply at air or surface temperatures below 8°C or when likely to rain before the paint has fully dried
Stir the product thoroughly to ensure it is fully homogeneous, do not contaminate
For the best results apply by brush, roller or spray
Application tool type and quality may influence the finished appearance
Apply liberally and avoid overspreading
Not to be applied below 8°C
Under normal conditions the coating will be touch dry after 1 hour
Overcoating time for subsequent coats is 3-4 hours
Porous surfaces should be sealed with a first coat of MS11 Multi-Surface Renovation Paint thinned with up to 20% clean water
On sealed surfaces apply two to three coats, allowing each coat to dry thoroughly
Spraying can considerably reduce the coverage rate depending on the type of spray equipment used
Please Note: Not suitable for areas under constant water contact such as shower cubicles or areas of high traffic such as worktops and handrails. Substrates which have had water-repellent preservative treatments applied should be avoided because adhesion could be compromised. Can be used on glass internally but not externally. Not recommended for horizontal decking areas and floors. Hot surfaces such as radiators should be coated when cold and allowed to dry before resuming heat. Paint will be fully hardened after 1 month
Coverage
Approximately 12 to 15m²/Litre per coat dependant on the nature and porosity of the surface
Rough surfaces will significantly reduce the coverage rates
Cleaning
All equipment must be washed with clean, cold water immediately after use
Waste material should not be emptied in the drainage systems
Some local authorities have special facilities for the disposal of leftover paint
Please do not add any product into drains or watercourses
Storage
When stored unopened in a dry place at temperatures above 5°C, shelf life is 12 months from the date of manufacture
If you have any left over product, ensure that you close the tin by replacing the lid firmly and securely and store in a safe place
PROTECT FROM FROST
To avoid the risk of spillage, always store and transport in a secure upright position
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Wethertex MS11 Multi-Surface Renovation Paint is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
General Painting Application Kit from Rawlins Paints provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site.
Provides an economical way of making sure you will have what you need
Ideal for interior and exterior paint projects
Click to jump down to...
Wethertex C10 Multi-Surface Fungicidal Wash is a ready to use, water based masonry wash for the removal of a broad range of bacterial, algal and fungal growth on masonry surfaces prior to painting. Developed using fast acting bioactive technology, the product is particularly effective against algae and mould growth and creates a clean surface,...
Wethertex ST1 Quick Dry Stabilising Primer is the ideal product for use when preparing unstable exterior surfaces for painting. Specially developed using fine particle sized polymers, this silicone based product is able to penetrate deep into the substrate, creating ultra high adhesion and high vapour permeability.
Seals and stabilises...
Wethertex S.A. Quicklock Textured Roller sleeves and frames for applying products such as Wethertex HBS Flex-Coat Hi-Build Coating.
Choose from individual 7" and 10" roller sleeves and frames, or sets from the menu below.
More Information Delivery Info Wethertex 2021 Brochure
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3).
Please click here for important information about these kits.
Kit Contents:
SET 1 (Hand Tools)
1 x Rust-Oleum...