Bradite Floor Finish

CF22

We no longer stock this product, but can recommend Teamac Chlorvar Chlorinated Rubber Paint as a great alternative.

Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to discuss your project.

Bradite Floor Finish is a high performance single pack chlorinated rubber floor paint for use on concrete and steel floors.

  • Available in more than 350 colours in RAL & BS
  • Quick drying floor paint with excellent water and good chemical resistance
  • Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems

Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.

Product customisation

Don't forget to save your customization to be able to add to cart
  • 250 char. max
Quantity
Product not available
This Product has been Discontinued

Description

Quick Links - Click To Jump To Section:




Features & Benefits


  • Available in more than 350 colours in RAL & BS
  • High performance single pack chlorinated rubber floor paint
  • Excellent water and good chemical resistance
  • For use on concrete and steel floors
  • Can be used with Bradite Low Slip Additive LS30 to provide additional under foot traction
  • Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems



Preparation


  • For internal and external steel or concrete and other external mineral substrates, which are dry, free of efflorescence laitance and have been properly prepared
  • Compatibility with existing coatings should be confirmed by preparing and painting a test patch. External floor surfaces may be suitable (well above local water table and/or an intact DPM barrier present)
  • Substrates should be dust free and completely dry before coating. When painting concrete it is vital to ensure that the substrate is completely dry and free of laitance
  • If the concrete is loose, chipping or has concrete dust present, the coating will not perform properly unless all loose material and dust is removed and damaged areas are repaired
  • Power floated, shiny or unpainted non porous concrete floors should be thoroughly vacuum blast cleaned to a roughness profile of 30-50 microns, or acid etched using Bradite Acid Etch TA37, or primed using Bradite Floor Primer ES40
  • High pressure water cleaning should be utilised to remove all loose and flaking paint and contamination back to a sound substrate. Bradite TD39 Industrial Degreaser should be used if necessary to remove all grease and oil
  • Intact areas of existing coatings should be roughened by abrasive manual or disc rubbing and feathered back to a sound coating edge. Cracks and pits should be filled using a suitable screed or mortar before painting



Application


  • Application and use should always conform to the codes of practice described in BS 6150 and BS 5493
  • For application on concrete or other absorbent substrates, the first coat should be thinned 15-20% with Bradite Thinner TC32 to allow penetration into the substrate
  • For maintenance painting the 1st coat will be a touch up to bare areas
  • Applicable by brush or roller. Spray is not recommended for this product
  • Supplied ready for use. Thin, if required, with 0 - 5% Bradite Thinner TC32
  • For additional underfoot traction, Bradite Low Slip Hard Aggregate LS30 should be added to the paint and mixed thoroughly just before use at a rate of 1 x 250ml LS30 tin (400g) per 5 litre of paint
  • Clean all equipment immediately after use with Bradite Thinner TC32 for best results
  • Surface dry in 1 hour. While the coating will take light foot traffic after overnight drying, full cure may take 4 days at 20°C, and should not be subject to heavy traffic for at least 24 hours. Please note that drying/curing times will vary depending on film thickness, temperature and relative humidity



Product Details
CF22

Data sheet

Manufacturer
Bradite
For Use By
General Use
For Use On
Concrete, Steel
Application Method
Brush, Roller, Spray
Sheen
Semi Gloss (20%)
Colour
Fully Tintable
VOC Levels
498 g/L
Single, Two or Three Pack
Single
Pack Size
5L
Application
Brush, Roller, Spray
Dry to Recoat (at 20°C)
12 hours - unlimited
Fully Cured (at 20°C)
6 days
Coverage
10m2 per Litre
Recommended Thinner/Cleaner
Bradite Thinner TC32
Min. Application Temperature
Down to 0°C (but must be 3°C above dew point)
Density
1.42 kg/L
Solids by Volume
45%
Shelf Life (from date of manufacture)
12 months minimum in original unopened containers
Touch Dry
1 hour
Recommended Dry Film Thickness
45 microns/coat
Recommended Wet Film Thickness
100 microns/coat
UN Number
UN1263
Dry for Light Traffic (at 20°C)
24 hours minimum, after final coat
Flashpoint
(Abel closed cup) 26°C
Colour(s)
Fully Tintable
Base Type
Solvent-Based
Exterior / Interior Use
Exterior & Interior Use
Suitable For Use On
Steel
Suitable For Use On
Concrete Floors
Finish
Semi-Gloss
Application Method
Brush
Application Method
Roller
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

Bradite Floor Primer

We no longer stock this product, but can recommend Rust-Oleum 3366 Epoxy Powerfloat Floor Primer Rapid as a great alternative. Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our...

In stock

Bradite Acid Etch

Bradite Acid Etch is a mineral acid solution used as a pre-treatment for bare concrete surfaces, for application to bare concrete floors to remove excess lime and/or to etch a surface profile to smooth concrete. Provides improved adhesion of subsequent floor coatings Manufactured under the auspices of an ISO 9001:2008 quality & ISO...

Price £24.18 (ex. VAT)
In Stock and Available for Delivery

Bradite Industrial Degreaser

Bradite Industrial Degreaser is an aqueous alkaline low foaming detergent used for degreasing contaminated surfaces prior to painting. Ideally suited for degreasing oily or soiled surfaces and for removing road dirt Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems More...

Price £7.28 (ex. VAT)
In Stock and Available for Delivery

Bradite TC32 Chlorinated Rubber/Pliolite Thinner

We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product. Bradite TC32 Chlorinated Rubber/Pliolite Thinner is a high flash point aromatic solvent for thinning alkyd based paints and equipment cleaning....

In stock

Bradite Low Slip Additive (LS30)

Bradite Low Slip Additive (LS30) is a hard Aluminium Oxide aggregate additive providing additional under foot traction to floor coatings, used in conjunction with Bradite floor paints requiring a hard wearing low slip additive and added to the paint and mixed thoroughly just before use. Manufactured under the auspices of an ISO 9001:2008...

Price £10.27 (ex. VAT)
In Stock and Available for Delivery