RSL Resustat CP

REPRB

RSL Resustat CP (formerly known as Resustat Primer) is designed to be applied prior to the use of Resustat ESM, Resustat SL23, Resustat TG69 or Resustat Terrazzo. It is a low viscosity epoxy primer with conductive fillers. 

Features and Benefits: 

  • Conductive with very low electrical resistance
  • Good adhesion
  • Low odour
  • High solids
  • Easy to apply
Colour
Size
Finish
£131.80
VAT excluded

£158.16 Tax incl.
Quantity

Description

RSL Resustat CP (formerly known as Resustat Primer) can be applied to wood, concrete, metal and synthetic floors. It is for application before static-dissipative resin flooring systems, which are ideal for industrial and domestic environments with high levels of electrical current. 

Resustat CP has a conductivity level of less than 0.050 M Ohms when tested in compliance with BS EN 61340.

Recommended Uses

  • Food halls
  • Breweries
  • Abattoirs
  • Operating theatres
  • Pharmaceuticals
  • TV studios
  • Prior to applying any of the Resustat range

Preparation

New Concrete Floors: New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding. A minimum strength of 25N/mm sq. is required.

Existing Concrete Floors: Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue of detergent is washed and removed by rinsing with clean water. Local repairs should be carried out with Resuscreed PA.

Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with existing floor coating.

Resustat CP can also be applied to existing coatings and to other cementitious screeds which should be clean and sound with an appropriate mechanical key for adhesion.

Priming

Resustat CP should be used as a conductive primer only and is normally applied on top of an already primed and sealed surface. The copper tape grid for the earthing should be applied prior to the application of the Resustat CP.

Open and porous substrates will require priming with Resuseal WB (clear) or Resuprime ST may be used as primer on the dry substrates only, with less than 75% ERH reading.

Where the relative humidity of a substrate exceeds 75% ERH, Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.

The number of coats to be applied is chosen in accordance with the following table:

ERH% Required Coating Thickness
75-85 1coat of Resuprime MVT at 200 microns per coat
85-92 2coats of Resuprime MVT at 200 microns per coat
92-97 3coats of Resuprime MVT at 200 microns per coat

Application

The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 10°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally, to allow the ambient and substrate temperature to stabilise prior to installation.

Mixing: Pre-mix the base component to a uniform consistency then mix the entire contents of the base with the hardener. If a separate mixing bucket is being used for mixing, ensure all contents of both components are removed from the buckets supplied. Mix using a slow speed electric mixer for approximately two to three minutes until the two components have fully combined.

The mixed unit should be applied immediately by roller or brush with a consistent procedure. Floor areas should be cross-rolled to ensure even application and to minimise roller marks.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
REPRB

Data sheet

For Use On
Concrete
Application Method
Brush, Roller, Squeegee
Sheen
Textured Gloss
Colour
Standard / Ready Mixed
VOC Levels
Low (50-149 g/l)
Single, Two or Three Pack
Two-Pack
Pack Size
5KG
Application
Brush, Roller
Coverage
5kg will cover 21.7m sq. @ 200 microns WFT.
Touch Dry
8 Hours.
UN Number (Activator)
UN3066
UN Number (Base)
UN3082
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

RSL Resuseal WB

Resuseal WB is a multi-purpose, two-pack, water-based epoxy coating primarily for concrete walls and floors. It can also be applied to concrete poured 7 days prior, as well as wood for a dust-free finish.  Low odour  Silica Free  Superb adhesion  Hard wearing  Hygienic Dust-free Some product colours are made to order and have minimum...

Price £50.53
In stock

RSL Resuprime ST

Resuprime ST (formerly known as Resuprime) is a two-pack, solvent-free epoxy resin bonding and priming coat. It bonds resin-based screeds and toppings to cementitious and other surfaces.  Features and Benefits: Versatile for many types of application Excellent adhesive properties Easy to apply Can be used as a tack coat for screeds No...

Price £68.19
In stock

RSL Resuprime MVT

RSL Resuprime MVT (formerly known as R.S. Dampshield FH) is a faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood.  Features and Benefits:...

Price £19.80
In stock

RSL Resuscreed PA

RSL Resuscreed PA (formerly known as Resupatch) is a three-pack epoxy resin mortar designed for rapid concrete repair in heavy duty environments. Features and Benefits:  Excellent mechanical properties Can be feather edged Abrasion and impact resistant Dust-free Concrete like in appearance Easy to apply Minimum surface preparation

Price £38.44
In stock